AvidAqua Sawfish Frag Rack Overview The AvidAqua Sawfish Frag Rack is a sleek, full-capacity magnetic rack designed to maximize plug space while preserving flow and light. Its sawfish-inspired outline hugs rockwork and narrow panes, keeping your aquascape clean as frags grow out. Key Features Magnetic mount for quick placement/repositioning (verify pane-thickness rating) High plug capacity in a low-profile footprint Reef-safe acrylic with encapsulated, corrosion-resistant magnets Standard plug fit—accepts most ½″ (≈12–13 mm) stems Chamfered holes seat plugs upright and reduce wobble Flow-friendly silhouette minimizes shadows and dead spots Lift-out design for easy cleaning and fast frag swaps Setup & Use Choose a spot with moderate flow and appropriate PAR. Clean the mounting area; remove film/salt creep. Place the wet side inside the tank and align the dry side outside. Seat plugs fully; leave 1–2″ between aggressive species. Light-acclimate new frags by starting lower and moving up over 1–2 weeks. Care & Maintenance Rinse in tank water during water changes; soft-brush detritus as needed. Inspect magnet encasement regularly; discontinue if coating is compromised. Avoid trapping sand/grit between the rack and pane. Product Specifications Product: AvidAqua Sawfish Frag Rack Material: CNC-cut reef-safe acrylic; encapsulated magnets Mounting: Magnetic (glass/acrylic compatible; confirm thickness rating) Frag Holes: Fits ½″ (≈12–13 mm) stems Use Case: Display or sump coral frag grow-out What’s in the Box AvidAqua Sawfish Frag Rack (magnetic mount)

AvidAqua Sawfish Accessory Frag Rack Overview The AvidAqua Sawfish Accessory Frag Rack is a slim, modular add-on rack that expands plug capacity without crowding your display. Its sawfish-inspired profile tucks into narrow spaces and around rockwork, keeping flow paths open while giving new frags the light and circulation they need. Key Features Magnetic mount for easy placement and repositioning (verify pane-thickness rating) Modular add-on design—pairs with main racks or runs solo in tight spots Reef-safe acrylic with encapsulated, corrosion-resistant magnets Standard plug fit—accepts most ½″ (≈12–13 mm) frag plug stems Chamfered holes keep plugs upright and reduce wobble Low shadowing silhouette preserves flow and PAR to surrounding corals Lift-out friendly for quick maintenance and frag swaps Setup & Use Choose a spot with moderate flow and suitable light. Clean the mounting area; remove salt creep/film. Place the wet side inside and align the dry side outside the pane. Seat frags fully in the holes; leave 1–2″ between aggressive species. Acclimate new frags by starting lower and moving up over 1–2 weeks. Care & Maintenance Rinse in tank water during water changes; soft-brush detritus as needed. Inspect magnet encasement periodically; discontinue use if the coating is compromised. Avoid trapping sand/grit between the rack and pane. Product Specifications Product: AvidAqua Sawfish Accessory Frag Rack Material: CNC-cut reef-safe acrylic; encapsulated magnets Mounting: Magnetic (glass/acrylic compatible; confirm thickness rating) Frag Holes: Fits standard ½″ (≈12–13 mm) stems Use Case: Add-on/space-saving frag grow-out in display or sump What’s in the Box AvidAqua Sawfish Accessory Frag Rack (magnetic mount)

AvidAqua Wyze Camera Mount with Lens Overview Get crisp reef footage and close-up polyp shots with the AvidAqua Wyze Camera Mount with Lens. A slim, angle-adjustable bracket locks your Wyze cam in place, while the included clip-on macro lens captures fine coral detail without moving the camera. Magnetic mounting keeps setup clean—no drilling or messy adhesives. Key Features Magnetic, tool-free install with secure ModMag-style mount (verify pane-thickness rating) Angle-adjustable bracket for perfect framing of display or sump Clip-on macro lens for tight detail (zoas, acros, inverts, feeders) Glare-control standoff and matte shroud reduce reflections at the glass Cable channels for tidy routing and safe drip loops Low-profile footprint—won’t block cabinet doors or snag cords Reef-safe construction; mount sits outside the tank Compatibility Fits cube-style Wyze Cam models (e.g., Cam v3/v3 Pro). Not designed for Pan/Tilt bases. Works on glass or acrylic panels (outside only); confirm magnet rating vs. pane thickness. Setup & Use Clean the panel where the mount will sit (remove dust/salt creep). Snap the camera into the adjustable bracket; route the USB through channels and create a drip loop. Place the outer magnet on the panel and attach the bracketed camera; adjust tilt/aim. Clip on the macro lens when you want close-ups; remove for full-tank shots. In the Wyze app, set IR (often off to avoid reflections), frame rate, and detection zone as desired. Tips For glare-free shots, aim slightly off-axis and dim room lights. Wipe the viewing pane before filming—fingerprints show up on camera. If shooting the sump, avoid direct splash zones. Care & Maintenance Wipe salt creep from bracket and cable during routine maintenance. Inspect magnet encasement; discontinue use if the coating is compromised. Keep sand/grit off mating surfaces. Product Specifications Product: AvidAqua Wyze Camera Mount with Lens Mounting: Magnetic external mount with angle adjustment Lens: Clip-on macro lens (removable) Materials: Marine-safe acrylic bracket; encapsulated magnets (external use) Placement: Outside of glass/acrylic; also suitable for cabinet/stand panels Use Case: Livestreams, macro coral videos, time-lapse, remote checks What’s in the Box Angle-adjustable Wyze camera bracket Clip-on macro lens Magnetic mount (outer hardware) Cable routing channels (integrated) Quick-start guide Note: Camera and power supply not included.

AvidAqua Wyze Camera Mount Kit with ModMag Overview Turn your Wyze cam into a reef monitor with the AvidAqua Wyze Camera Mount Kit. The included ModMag magnetic mount secures your camera to the outside of the tank or stand, while the low-profile bracket aligns the lens for clear viewing of your display or sump—no drilling, no messy adhesives. Key Features Magnetic, tool-free install—position/reposition in seconds (verify pane-thickness rating) Angle-adjustable bracket to fine-tune tilt for full-tank or macro views Cable management channels keep the USB lead tidy and drip-loop friendly Low-profile footprint—won’t block cabinet doors or snag cords Reef-safe construction with encapsulated, corrosion-resistant magnets (mount sits outside the tank) Splash guard lip helps deflect occasional salt creep near sump areas Compatibility Fits most Wyze Cam cube-style models (e.g., Cam v3/v3 Pro). Not intended for Pan/Tilt models with large bases. Mounts on the outside of glass or acrylic; confirm ModMag rating vs. your pane thickness. Works on vertical stand panels for side-angle shots. Setup & Use Clean the surface (remove dust/salt creep). Snap the camera into the angle bracket, route the USB cable through the channels. Place the ModMag outer half on the panel and attach the bracketed camera. Adjust tilt/aim; create a drip loop before the power supply. In the Wyze app, set your detection zone and IR preferences (disable IR if reflections occur). Tips For glare, shoot slightly off-axis and dim room lights. If filming the sump, avoid direct splash zones; use the splash lip as needed. Wipe the panel for clearer footage—fingerprints show up on camera. Care & Maintenance Wipe salt creep from the mount and cable during routine maintenance. Inspect magnet encasement periodically; discontinue if coating is compromised. Keep sand/grit off mating surfaces. Product Specifications Product: AvidAqua Wyze Camera Mount Kit with ModMag Includes: Angle-adjustable camera bracket, ModMag magnetic mount Materials: Reef-safe acrylic & encapsulated magnets (external use) Placement: Outside of glass/acrylic; cabinet/stand panels Use Case: Livestreams, time-lapse, top-off checks, nighttime observation What’s in the Box Angle-adjustable Wyze bracket ModMag magnetic mount (inner/outer halves) Cable routing clips/channels (integrated) Quick-start guide Note: Camera and power supply not included.

AvidAqua Traveler Trio Overview The AvidAqua Traveler Trio is a reef-safe three-chamber acclimation/observation box that mounts magnetically to your display or sump. Run simultaneous drip acclimations, isolate multiple fish/inverts, or stage frags—without nets, baskets, or clutter. Key Features Three independent chambers with removable dividers for flexible layouts Magnetic mount for hands-free placement (verify pane-thickness rating) Flow-through slots provide gentle water exchange while preventing escapes Lift-off lid with fine ventilation to reduce jump risk and splash Rounded, polished edges protect fins and coral tissue Reef-safe acrylic with encapsulated, corrosion-resistant magnets Common Uses Parallel drip acclimation for multiple new arrivals Short-term isolation/observation (time-outs, post-treatment recovery) Frag staging/recovery after transport or cutting Target feeding shy fish without competition Setup & Use Rinse in RO/DI before first use. Mount the wet side inside the tank/sump; align the dry side outside. Float briefly to match temperature, then allow tank water to circulate via slots. For drip acclimation, route airline(s) to each chamber and set a gentle drip. When finished, lift out, drain, and release livestock. Tips Place in moderate flow, away from direct powerhead blasts. Add a fine mesh liner if housing tiny inverts or fry. Keep the lid on for jump-prone species. Care & Maintenance Rinse with fresh water after use; clear salt creep from slots and lid. Inspect magnet encasement periodically; discontinue if coating is compromised. Avoid trapping sand/grit between magnets and pane. Product Specifications Product: AvidAqua Traveler Trio Type: Magnetic acclimation/transfer/observation box (three chambers) Material: Reef-safe acrylic; encapsulated magnets Mounting: Magnetic (glass/acrylic compatible; confirm thickness rating) Included: Lift-off lid; two removable dividers for three-zone configuration What’s in the Box Traveler Trio acclimation box (inner & outer magnetic halves) Two dividers (create three chambers) Lid Quick-start guide

AvidAqua Traveler Mini Overview The AvidAqua Traveler Mini is a compact, reef-safe acclimation/transfer box for fish, inverts, and frags. It magnetically mounts to your display or sump for hands-free temperature matching, drip acclimation, observation, and quick isolation—perfect when space is tight. Key Features Small footprint for nanos and cramped sumps Magnetic mount for secure, easy placement (verify pane-thickness rating) Flow-through slots allow gentle water exchange while preventing escapes Lift-off lid with fine ventilation to reduce jump risk and splash Rounded, polished edges to protect delicate fins and coral tissue Reef-safe acrylic with encapsulated, corrosion-resistant magnets Common Uses Drip acclimation & temp matching for small fish/inverts Short-term isolation/observation in the display Frag staging/recovery after transport or cutting Target feeding shy or new arrivals without competition Setup & Use Rinse in RO/DI before first use. Mount wet side inside the tank; align dry side outside. Float to match temperature, then hang and allow tank water to circulate via slots. For drip acclimation, route airline to the box and adjust to a gentle drip. When finished, lift out, drain, and release livestock. Tips Place in moderate flow, away from direct powerhead blasts. Add a fine mesh liner if housing very small inverts or fry. Keep the lid on for jump-prone species. Care & Maintenance Rinse with fresh water after use; clear salt creep from slots and lid. Inspect magnet encasement regularly; discontinue if coating is compromised. Avoid trapping sand/grit between magnets and pane. Product Specifications Product: AvidAqua Traveler Mini Type: Magnetic acclimation/transfer/observation box Material: Reef-safe acrylic; encapsulated magnets Mounting: Magnetic (glass/acrylic compatible; confirm thickness rating) Included: Box with lift-off lid What’s in the Box Traveler Mini acclimation box (inner & outer magnetic halves) Lid Quick-start guide

AvidAqua Traveler Mega Overview The AvidAqua Traveler Mega is a large-format, reef-safe acclimation/transfer box for fish, inverts, and corals. Magnetically mounts to your display or sump for hands-free acclimation, observation, isolation, and frag holding—so you can manage new arrivals and time-outs without nets, baskets, or clutter. Key Features Mega capacity for roomy acclimation of fish, inverts, or multiple frags Magnetic mount for secure, hands-free placement (verify pane-thickness rating) Flow-through slots provide gentle water exchange while preventing escapes Removable divider to separate livestock or stage frags Lift-off lid with fine ventilation to reduce jump risk and splash Rounded, polished edges to protect fish and delicate coral tissue Reef-safe acrylic with encapsulated, corrosion-resistant magnets Common Uses Drip acclimation & temperature matching (hang on the tank for stability) Observation/quarantine light (short-term isolation within the display) Frag staging before placement or for recovery after fragging/transport Feeding in isolation for shy/new fish without competition Setup & Use Rinse in RO/DI before first use. Mount the wet side inside the tank/sump and align the dry side outside. For acclimation, float to match temperature, then place and allow flow through the slots. Use the divider to separate inhabitants or to group frags. When finished, lift out, drain, and return livestock to the display. Tips Position in moderate flow, away from powerheads that could blast small occupants. For tiny inverts, add a fine mesh liner if needed to further reduce slot size. Keep the lid on for jump-prone species. Care & Maintenance Rinse with fresh water after use; wipe salt creep from slots and lid. Inspect magnet encasement regularly; discontinue use if coating is compromised. Avoid trapping sand/grit between the magnets and pane. Product Specifications Product: AvidAqua Traveler Mega Type: Magnetic acclimation/transfer/observation box Material: Reef-safe acrylic; encapsulated magnets Mounting: Magnetic (glass/acrylic compatible; confirm thickness rating) Included: Box with lift-off lid and removable divider What’s in the Box Traveler Mega acclimation box (inner & outer magnetic halves) Removable divider Lid Quick-start guide

AvidAqua Stingray Next Level Adapter Overview Take your frag capacity to the next tier—literally. The AvidAqua Stingray Next Level Adapter adds a raised, stackable platform to compatible Stingray racks, letting you stage fresh cuts higher for light acclimation, improve flow between tiers, and keep your layout tidy without adding more footprint. Key Features Stackable tier adds a second level to compatible Stingray frag racks Adjustable standoffs (multi-position height) for light acclimation and flow tuning Rigid, reef-safe acrylic with rounded edges to protect plugs and fingers Low-shadow design maintains PAR and crossflow to lower frags Tool-free install—snap/lock posts for a secure, wobble-free fit Standard plug holes fit most ½″ (≈12–13 mm) stems Setup & Use Remove the rack from the tank (or lower water level for easy access). Seat the adapter posts into the designated Stingray mounts until they click. Align the upper deck and press down to lock on all posts. Place new frags on the upper tier for acclimation, then rotate to lower tier as they harden. Leave 1–2″ spacing between aggressive species. Compatibility Designed for AvidAqua Stingray frag racks (model variants with adapter cutouts). Fits standard frag plug stems (~12–13 mm). Use in display or sump; verify clearance for skimmer lids and braces. Care & Maintenance Rinse with tank water during maintenance; soft-brush detritus as needed. Inspect posts/slots for salt creep; wipe clean for smooth on/off action. Avoid trapping sand/grit between deck and plugs. Product Specifications Product: AvidAqua Stingray Next Level Adapter Material: Reef-safe acrylic (CNC-cut) Height Options: Multi-position standoffs (model-dependent range) Frag Holes: Fits ½″ (≈12–13 mm) stems Use Case: Add-on tier for acclimation and capacity expansion What’s in the Box Upper adapter deck Standoff posts (quantity varies by model) Quick-start guide

AvidAqua Sawfish Accessory Frag Rack Overview The AvidAqua Sawfish Accessory Frag Rack is a slim, modular add-on rack that expands plug capacity without crowding your display. Its sawfish-inspired profile tucks into narrow spaces and around rockwork, keeping flow paths open while giving new frags the light and circulation they need. Key Features Magnetic mount for easy placement and repositioning (verify pane-thickness rating) Modular add-on design—pairs with main racks or runs solo in tight spots Reef-safe acrylic with encapsulated, corrosion-resistant magnets Standard plug fit—accepts most ½″ (≈12–13 mm) frag plug stems Chamfered holes keep plugs upright and reduce wobble Low shadowing silhouette preserves flow and PAR to surrounding corals Lift-out friendly for quick maintenance and frag swaps Setup & Use Choose a spot with moderate flow and suitable light. Clean the mounting area; remove salt creep/film. Place the wet side inside and align the dry side outside the pane. Seat frags fully in the holes; leave 1–2″ between aggressive species. Acclimate new frags by starting lower and moving up over 1–2 weeks. Care & Maintenance Rinse in tank water during water changes; soft-brush detritus as needed. Inspect magnet encasement periodically; discontinue use if the coating is compromised. Avoid trapping sand/grit between the rack and pane. Product Specifications Product: AvidAqua Sawfish Accessory Frag Rack Material: CNC-cut reef-safe acrylic; encapsulated magnets Mounting: Magnetic (glass/acrylic compatible; confirm thickness rating) Frag Holes: Fits standard ½″ (≈12–13 mm) stems Use Case: Add-on/space-saving frag grow-out in display or sump What’s in the Box AvidAqua Sawfish Accessory Frag Rack (magnetic mount)