Collection:  Aqua Ultraviolet

102 productos
  • Precio regular
    $13.75
    Precio de venta
    $13.75
    Precio regular
    Aqua Ultraviolet – Replacement Quartz Cap, Clear (with O-Ring) Overview Factory clear quartz cap for Aqua Ultraviolet UV sterilizers. Protects the quartz sleeve end while letting you visually confirm lamp-on status. Includes a new O-ring to restore a drip-tight seal. Key Features Genuine Aqua Ultraviolet clear cap for visual lamp check Includes O-ring sized for the factory groove Maintains a clean, sealed end-cap assembly to protect sleeve and wiring Tool-light swap; ideal when caps are crazed, cracked, or leaking Compatibility Aqua Ultraviolet Classic and SL models that use the clear quartz end cap Check your unit’s cap style and wattage family to ensure correct fit Specifications Part: Clear quartz cap with sealing O-ring Materials: Optical-clear cap; elastomer O-ring Use: External end-cap component (non-submersible) What’s Included (1) Clear quartz cap (1) O-ring Install & Care Notes Power off and depressurize the system. Remove the old cap; clean threads, groove, and sealing face. Lightly lube the new O-ring with silicone-safe grease and seat it evenly. Install the cap hand-tight, then snug—do not overtighten. Pressurize and leak-test; verify lamp illumination through the clear cap.
  • Precio regular
    $234.51
    Precio de venta
    $234.51
    Precio regular
    Aqua Ultraviolet – Replacement NEMA Transformer / Ballast for Classic 80 Watt Overview Factory replacement NEMA-enclosed transformer/ballast assembly for the Aqua Ultraviolet Classic 80W UV sterilizer (two 40-watt lamps). Restores reliable lamp ignition and correct operating current in a rugged, service-friendly outdoor-rated housing. Key Features Genuine Aqua Ultraviolet NEMA enclosure power unit Matched output for Classic 80W systems (2 × 40W lamps) Weather-resistant, wall-mountable housing with cord strain relief Stable start/run current to maintain consistent UV output Drop-in swap for failed or aging power supplies Compatibility Aqua Ultraviolet Classic 80 Watt UV sterilizers (all port sizes; wiper or non-wiper) Not for other wattages (8/15/25/57/114/120/160, etc.) Specifications Input: 120V AC, 60Hz (North America) Output: Factory-matched to Aqua UV 40W low-pressure UV-C lamps (×2) Enclosure: NEMA weather-resistant case, external/dry-location install only (non-submersible) Mounting: Keyhole/through-holes for wall or equipment board Leads/Connectors: Pre-wired lamp and line cords (style may vary by production) What’s Included (1) NEMA transformer/ballast assembly for Classic 80W Installation & Safety Notes Disconnect power and isolate plumbing before service. Mount the NEMA box upright in a dry, ventilated area away from spray. Wire/plug per the factory diagram; confirm line/neutral/ground. Route lamp leads with strain relief; avoid sharp bends or pinch points. After installation, verify each lamp strikes and operates steadily; replace aged lamps/sleeves as needed. Want me to turn this into a single-row Shopify CSV with your standard columns and tags?
  • Precio regular
    $25.33
    Precio de venta
    $25.33
    Precio regular
    Aqua Ultraviolet – Replacement EZ Twist Top, White (with O-Ring) Overview Factory EZ Twist top cap for Aqua Ultraviolet UV sterilizers. Replaces a cracked, stripped, or leaking top and restores a tool-free seal over the quartz sleeve/end-cap assembly. Includes a new O-ring for a drip-tight fit. Key Features Genuine Aqua Ultraviolet EZ Twist replacement top (white) Includes O-ring sized for the factory groove Tool-free on/off for fast lamp and sleeve service Durable, UV- and chemical-resistant construction Compatibility Aqua Ultraviolet Classic and SL models that use the EZ Twist style top Fit varies by wattage/body—verify your unit’s top style before ordering Specifications Part: EZ Twist top cap — White Seal: Matching O-ring (included) Material: Heavy-duty polymer Use: External end-cap component (non-submersible) What’s Included (1) EZ Twist top cap — white (1) O-ring for the cap Install & Care Notes Power off and depressurize the system. Remove old cap; clean threads and the O-ring groove/sealing face. Lightly lubricate the new O-ring with silicone-safe lube; seat evenly. Thread the cap on by hand and snug—do not overtighten. Pressurize and leak-test; recheck after the first run cycle.
  • Precio regular
    $584.29
    Precio de venta
    $584.29
    Precio regular
    Overview Factory lamp kit for the Aqua Ultraviolet VIPER 400W UV sterilizer with 3" stainless steel housing. Restores peak germicidal performance in large, high-flow systems using a single high-output, low-pressure (amalgam) UV-C lamp. Key Features Genuine Aqua UV 400-watt HO UV-C lamp matched to 3" stainless VIPER units OEM-matched components to maintain correct fit, sealing, and UV dose Service-friendly kit minimizes downtime on critical life-support loops Ideal for aquaculture, big ponds, and commercial aquarium systems Compatibility For VIPER 400W sterilizers in 3" stainless steel configuration Not compatible with 2" stainless or 3" plastic VIPER bodies, nor other wattages (800W/1200W) Specifications Lamp Power: 400 W (low-pressure amalgam UV-C) Peak Wavelength: ~254 nm (germicidal) Housing Fit: 3" stainless VIPER chamber Service Life: Replace about every 9–12 months of continuous use (or per UV meter/dose targets) What’s Included (1) 400W UV-C lamp — VIPER, 3" stainless fit (1) Set of end seals/O-rings sized for the 3" stainless end assembly (1) Set of required end hardware/insulator(s) (kit dependent) Quick install sheet Installation & Safety Notes Disconnect power and let the unit cool. Isolate and depressurize plumbing; drain the chamber. Open end assembly; remove old lamp/seals (avoid touching new lamp glass). Inspect/clean the quartz sleeve; replace if cloudy, etched, or cracked. Lightly lube new O-rings with silicone-safe grease; seat squarely. Reassemble hand-tight, then snug—do not overtighten. Restore flow, power ON, verify strike, and check for leaks after first run.
  • Precio regular
    $584.29
    Precio de venta
    $584.29
    Precio regular
    Aqua Ultraviolet – VIPER 400W Lamp Kit, 2" Stainless Steel Overview Factory lamp kit for the Aqua Ultraviolet VIPER 400W UV sterilizer with 2" stainless steel housing. Restores peak germicidal performance for large, high-flow systems using a single high-output, low-pressure (amalgam) UV-C lamp. Key Features Genuine Aqua UV 400-watt HO UV-C lamp matched to 2" stainless VIPER units Maintains correct fit, sealing, and UV dose for reliable operation Service-friendly kit minimizes downtime on critical life-support systems Ideal for aquaculture, large ponds, commercial displays, and LSS loops Compatibility For VIPER 400W sterilizers in 2" stainless steel configuration Not compatible with 3" plastic VIPER bodies or other wattages (800W/1200W) Specifications Lamp Power: 400 W (low-pressure amalgam UV-C) Peak Wavelength: ~254 nm (germicidal) Housing Fit: 2" stainless VIPER chamber Service Life: Replace about every 9–12 months of continuous use (or per UV meter/dose targets) What’s Included (1) 400W UV-C lamp — VIPER, 2" stainless fit (1) Set of end seals/O-rings sized for stainless VIPER end assembly (1) Set of required end hardware/insulator(s) (kit dependent) Quick install sheet Installation & Safety Notes Disconnect power and allow the unit to cool fully. Isolate and depressurize plumbing; drain the chamber. Open end assembly; remove old lamp and seals (avoid touching new lamp glass). Inspect/clean the quartz sleeve; replace if etched, cloudy, or cracked. Lightly lube new O-rings with silicone-safe grease; seat squarely. Reassemble hand-tight, then snug—do not overtighten. Restore flow, power ON, verify strike, and check for leaks after first run.
  • Precio regular
    $584.29
    Precio de venta
    $584.29
    Precio regular
    Aqua Ultraviolet – VIPER 400W Lamp Kit for 3" Plastic Unit Overview Factory lamp kit for the Aqua Ultraviolet VIPER 400W (3" plastic) sterilizer. Restores peak germicidal performance in high-flow, large-system applications using a single high-output, low-pressure (amalgam) UV-C lamp. Key Features Genuine Aqua UV 400-watt HO UV-C lamp for VIPER 3" plastic housings Matched components to maintain proper fit, sealing, and UV dose Fast, service-friendly swap to keep downtime to a minimum Supports clear water and pathogen reduction in demanding, high-GPH systems Compatibility For VIPER 400W UV sterilizers with the 3" plastic body Not for stainless units or other wattages (800W/1200W) Specifications Lamp Power: 400 W (low-pressure UV-C, amalgam) Peak Wavelength: ~254 nm germicidal Housing Fit: 3" plastic VIPER assembly Service Life: Replace ~9–12 months of continuous use (or per meter/dose targets) What’s Included (1) 400W UV-C lamp (VIPER, 3" plastic fit) (1) Set of end seals/O-rings matched to the lamp end assembly (1) Quartz end cap/insulator or hardware as required for this kit (model dependent) Quick install sheet Contents may vary slightly by production run; all parts are OEM and matched for the 3" plastic VIPER 400W. Installation & Safety Notes Power OFF and lock out the circuit; allow the unit to cool. Isolate and depressurize plumbing; drain the UV chamber. Open end assembly, remove old lamp and seals; do not touch new lamp glass with bare hands. Inspect/clean the quartz sleeve; replace if etched or cracked. Install new seals lightly lubricated with silicone-safe grease; seat squarely. Reassemble hand-tight, then snug—do not overtighten. Restore flow, then power ON and verify operation; check for leaks after first run.
  • Precio regular
    $7.78
    Precio de venta
    $7.78
    Precio regular
    Aqua Ultraviolet – Union Ring (Nut), 2" — White Overview OEM replacement 2" union ring (nut) for Aqua Ultraviolet UV sterilizers and filters. Replaces cracked or stripped rings to restore a secure, serviceable, leak-free connection. Key Features Genuine Aqua Ultraviolet 2" union ring Durable, chemical- and UV-resistant white polymer Knurled/ergonomic profile for easy hand-tightening Works with factory union halves and O-rings for drip-tight seals Compatibility Fits Aqua Ultraviolet Classic / SL / Ultima components that use 2" slip/socket unions Pairs with the standard 2" union body/half and 2" union O-ring (O-ring not included) Specifications Part: Union ring (nut) — 2", white Material: Corrosion-resistant engineered polymer Use: External plumbing; non-submersible component What’s Included (1) 2" white union ring (nut only; O-ring and tailpieces sold separately) Installation Notes Inspect union faces and replace the O-ring if flattened or cracked. Lightly lube the O-ring with silicone-safe grease and seat it in the groove. Align union halves and thread the ring on hand-tight, then snug—do not overtighten. Pressurize and leak-test.
  • Precio regular
    $7.78
    Precio de venta
    $7.78
    Precio regular
    Aqua Ultraviolet – Union Ring, 2" (Black) Overview OEM replacement 2" union ring (nut) for Aqua Ultraviolet UV sterilizers and filters. Restores a secure, serviceable connection when the original ring is cracked, stripped, or missing. Key Features Genuine Aqua Ultraviolet 2" union ring Durable, chemical- and UV-resistant black polymer Knurled/ergonomic profile for easy hand-tightening Works with factory union halves and O-rings for drip-tight seals Compatibility Fits Aqua Ultraviolet Classic / SL / Ultima components that use 2" slip/socket unions Matches factory 2" union body/half and standard 2" union O-ring (O-ring not included) Specifications Part: Union ring (nut) — 2", black Material: Corrosion-resistant engineered polymer Use: External plumbing; non-submersible part What’s Included (1) 2" black union ring (nut only; O-ring and tailpieces sold separately) Installation Notes Inspect mating union faces and replace the O-ring if flattened or cracked. Lightly lube O-ring with silicone-safe grease, seat in groove. Align union halves and thread the union ring on hand-tight, then snug—do not overtighten. Pressurize and leak-test.
  • Precio regular
    $17.55
    Precio de venta
    $17.55
    Precio regular
    Aqua Ultraviolet – Union Half 3/4" Reducer Bushing (No Thread) with O-Ring — White Overview OEM reducer union half that adapts an Aqua Ultraviolet union to 3/4" without threads. Ideal when converting from larger union bodies to 3/4" smooth (slip/socket) plumbing. Includes a fresh O-ring for a drip-tight seal. Key Features Genuine Aqua Ultraviolet union half + reducer bushing No-thread (smooth) interface for solvent-weld PVC connections Includes O-ring sized for the factory groove Durable, chemical- and UV-resistant white polymer Compatibility Fits Aqua Ultraviolet Classic / Advantage / SL unions that accept interchangeable tails/reducer bushings Use when stepping down union connection to 3/4" slip; verify your union body style before ordering Specifications Size: Union half with 3/4" reducer bushing (smooth, no threads) Seal: Matching O-ring (included) Color/Material: White engineered polymer Use: External plumbing; non-submersible component What’s Included (1) Union half with integrated 3/4" reducer bushing — white (1) Union O-ring Installation Notes Shut off pump and relieve pressure. Clean union faces and groove; lightly lube O-ring with silicone-safe grease. Seat O-ring, solvent-weld 3/4" PVC into the smooth bushing (allow full cure). Assemble union hand-tight, then snug—do not overtighten. Pressurize and leak-test.
  • Precio regular
    $20.37
    Precio de venta
    $20.37
    Precio regular
    Aqua Ultraviolet – ULTIMA II Valve Cover O-Ring (for 1.5" Valve) Overview OEM replacement valve cover O-ring for Aqua Ultraviolet Ultima II filters equipped with the 1.5" multi-port valve. Restores a drip-tight seal on the valve lid to stop leaks and prevent air draw. Key Features Genuine Aqua Ultraviolet 1.5" valve cover seal Resilient elastomer for long service life Seats easily; compatible with silicone-safe lubricants Quick, tool-light fix for weeping lids or flattened gaskets Compatibility Fits Ultima II filters using the 1.5" multi-port valve (e.g., 1,000 / 2,000 / 4,000 models and any kit with a 1.5" valve) For 2" valves (6,000/10,000/20,000), use the corresponding 2" valve cover O-ring Specifications Part Type: Valve cover O-ring (lid seal) Size: For 1.5" multi-port valve assembly Material: Durable elastomer (black) Use: External sealing surface (non-submersible component by itself) What’s Included (1) Valve cover O-ring for 1.5" Ultima II valve Installation Notes Shut off pump and relieve system pressure; set valve to Closed. Remove the valve cover; pull the old O-ring and clean the groove and mating face. Lightly coat the new O-ring with silicone-safe lubricant—avoid petroleum products. Seat evenly, reinstall the cover hand-tight, then snug—do not overtighten. Pressurize and leak-test; recheck after the first backwash cycle.
  • Precio regular
    $30.65
    Precio de venta
    $30.65
    Precio regular
    Aqua Ultraviolet – ULTIMA II Filter O-Ring (for 1,000–20,000 Models) Overview OEM replacement tank/valve O-ring for Aqua Ultraviolet Ultima II pressurized filters. Restores a drip-tight seal between the multi-port valve and filter body to stop leaks and air draw. Key Features Genuine Aqua Ultraviolet seal for Ultima II filters Sized to fit the full family: 1,000 / 2,000 / 4,000 / 6,000 / 10,000 / 20,000 Resilient elastomer; compatible with silicone-safe lubricants Quick, tool-light fix for weeping or flattened gaskets Compatibility Aqua Ultraviolet Ultima II filters from 1,000 up to 20,000 gallons Seats between the multi-port valve and filter vessel lid (verify placement in your manual) Specifications Part Type: Valve-to-tank O-ring Material: Durable elastomer (black) Environment: External, wet-location seal (non-submersible component by itself) What’s Included (1) ULTIMA II O-ring (fits 1,000–20,000 series) Installation Notes Shut off pump and relieve pressure; set valve to Closed. Remove the multi-port valve; lift out the old O-ring and clean groove/mating faces. Lightly coat the new O-ring with silicone-safe lubricant—no petroleum products. Seat evenly in the groove; reinstall valve hand-tight, then snug—do not overtighten. Pressurize and leak-test; recheck after the first backwash cycle.
  • Precio regular
    $2,629.94
    Precio de venta
    $2,629.94
    Precio regular
    Aqua Ultraviolet – Ultima II 6,000 Filter with 2" Multi-Port Valve Overview Robust, pressurized bead/bio filter for ponds and water features up to 6,000 gallons. The Ultima II 6,000 combines non-clogging media with a powerful cyclonic backwash to keep water crystal clear with minimal routine maintenance—ideal for koi ponds and heavily stocked water gardens. Key Features Bead + biological filtration using high–surface-area Bio-Tubes media Cyclonic backwash lifts and purges debris fast—no messy media cleaning 2" multi-port valve with simple handle positions (Filter, Backwash, Rinse, Waste, Recirculate, Closed) Low head-loss design supports long plumbing runs and external pumps UV- and weather-resistant, corrosion-proof vessel for outdoor pads (non-submersible) Sizing & Flow Guidance Pond capacity: up to 6,000 gal (heavy fish load/full sun may require upsizing) Target pump flow: ~4,000–6,000 GPH through the 2" valve for best performance Backwash when the pressure gauge rises ~5–8 psi above clean baseline Specifications Model: Ultima II 6,000 Valve: 2" side-mount multi-port Ports: 2" slip at valve (adapt as needed) Operation: Pressurized, backwashable bead/bio-media system Installation: Outdoor-ready; level, well-supported base Warranty: Manufacturer limited warranty on tank/valve (see terms) What’s Included Ultima II 6,000 filter vessel pre-loaded with media 2" multi-port valve (handle & sight glass) Union/tailpiece set (model dependent) Quick start/installation guide Installation Notes Place on a level, load-bearing pad near pump and returns. Plumb pump to valve IN, valve OUT to pond/returns; add a WASTE line for backwash. Use unions and 2" PVC to minimize head loss; keep runs smooth and short. On first start, run Rinse briefly, then switch to Filter. Backwash at +5–8 psi or on a regular schedule for high-load systems.
  • Precio regular
    $3,519.87
    Precio de venta
    $3,519.87
    Precio regular
    Aqua Ultraviolet – Ultima II 10,000 Filter w/ 2" Multi-Port Valve Overview High-capacity, pressurized bead filter for ponds and water features up to 10,000 gallons. The Ultima II 10,000 combines dense, non-clogging bio-media with a powerful backwash system to deliver crystal-clear water with minimal maintenance. Key Features Pressurized “bead” filtration with high-surface-area Bio-Tubes for mechanical + biological polishing Cyclonic backwash agitates and lifts debris for fast, low-waste cleaning 2" multi-port valve (side-mount) with simple handle positions (Filter, Backwash, Rinse, Waste, Recirculate, Closed) Low headloss design—pairs well with external pumps on long runs UV- and weather-resistant, corrosion-proof vessel for outdoor equipment pads Sizing & Flow Guidance Pond capacity: up to 10,000 gal (stocking/feeding and sun exposure may reduce real-world capacity—oversize when in doubt) Typical pump pairing: ~7,500–10,000 GPH target flow through the 2" valve For koi/high load, consider upsizing pump/filter or running a prefilter for best results Specifications Model: Ultima II 10,000 Valve: 2" side-mount multi-port Operation: Pressurized, backwashable bead/bio-media system Ports: 2" slip (common) at valve ports (adapt as needed) Orientation: Outdoor-ready (non-submersible); level pad or equipment stand Warranty: Manufacturer limited warranty on tank/valve (see terms) What’s Included Ultima II 10,000 filter vessel pre-loaded with media 2" multi-port valve (handle, sight glass) Union set / tailpieces (model dependent) Backwash drain/waste port Quick start/installation guide Installation Notes Place on a level, load-bearing pad near pump and returns. Plumb pump to valve IN, valve OUT to pond/returns; add waste line for backwash. Use unions and 2" PVC where possible to minimize headloss. Start in Rinse after media loads with water, then set to Filter. Backwash when the pressure gauge rises ~5–8 psi above clean baseline (or weekly in heavy-load ponds).
  • Precio regular
    $707.51
    Precio de venta
    $707.51
    Precio regular
    Aqua Ultraviolet – TWIST 40 Watt UV Sterilizer, 2" (White) Overview Mid-size UV-C sterilizer with a flexible plumbing layout. The TWIST 40W adds a rotatable union block so you can “twist” the inlet/outlet orientation to match your run—cutting elbows, head loss, and install time. 2" slip ports support high-flow pond and aquarium loops. Key Features Rotating (TWIST) union block aligns ports to your plumbing in tight spaces Single 40W low-pressure UV-C lamp targets algae, bacteria, and protozoa 2" slip inlet/outlet for clean, high-flow PVC installs Clear end cap shows lamp-on status; service-friendly access Weather-resistant housing (non-submersible) for indoor or protected outdoor use Sizing & Flow Guidance Sterilizer (freshwater): ~1,200–2,000 gal Sterilizer (saltwater): ~325 gal Clarifier (freshwater): up to ~6,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): ~2,900 GPH ≈ 30,000 µW·s/cm² (clarifying) ~1,930 GPH ≈ 45,000 µW·s/cm² ~1,450 GPH ≈ 60,000 µW·s/cm² ~1,160 GPH ≈ 75,000 µW·s/cm² ~967 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: TWIST 40 Watt, 2" Inlet/Outlet, White Lamp: (1) × 40W low-pressure UV-C Electrical: 120 V / 60 Hz Connections: 2" slip (in/out), rotatable union block Dimensions (unit): ≈38" × 4" × 2.5" Cord Length: ~15 ft Mounting: Wall/stand or supported inline (use appropriate brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included TWIST 40W UV body (White, 2" ports) (1) 40W UV lamp Transformer/power supply Union/slip set Quick start/installation guide Installation Notes Install after mechanical filtration on a pressurized return line. Rotate (twist) the union block to align with your plumbing, solvent-weld, and allow full cure before pressurizing. Add unions/valves to isolate the unit and dial in target flow. Protect from weather; do not submerge. Replace the lamp every 9–12 months for consistent UV dose; clean/inspect the quartz sleeve at each change.
  • Precio regular
    $648.89
    Precio de venta
    $648.89
    Precio regular
    Aqua Ultraviolet – TWIST 40 Watt UV Sterilizer, 2" (White) Overview Mid-size UV-C sterilizer with a flexible plumbing layout. The TWIST 40W adds a rotatable union block so you can “twist” the inlet/outlet orientation to match your run—cutting elbows, head loss, and install time. 2" slip ports support high-flow pond and aquarium loops. Key Features Rotating (TWIST) union block aligns ports to your plumbing in tight spaces Single 40W low-pressure UV-C lamp targets algae, bacteria, and protozoa 2" slip inlet/outlet for clean, high-flow PVC installs Clear end cap shows lamp-on status; service-friendly access Weather-resistant housing (non-submersible) for indoor or protected outdoor use Sizing & Flow Guidance Sterilizer (freshwater): ~1,200–2,000 gal Sterilizer (saltwater): ~325 gal Clarifier (freshwater): up to ~6,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): ~2,900 GPH ≈ 30,000 µW·s/cm² (clarifying) ~1,930 GPH ≈ 45,000 µW·s/cm² ~1,450 GPH ≈ 60,000 µW·s/cm² ~1,160 GPH ≈ 75,000 µW·s/cm² ~967 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: TWIST 40 Watt, 2" Inlet/Outlet, White Lamp: (1) × 40W low-pressure UV-C Electrical: 120 V / 60 Hz Connections: 2" slip (in/out), rotatable union block Dimensions (unit): ≈38" × 4" × 2.5" Cord Length: ~15 ft Mounting: Wall/stand or supported inline (use appropriate brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included TWIST 40W UV body (White, 2" ports) (1) 40W UV lamp Transformer/power supply Union/slip set Quick start/installation guide Installation Notes Install after mechanical filtration on a pressurized return line. Rotate (twist) the union block to align with your plumbing, solvent-weld, and allow full cure before pressurizing. Add unions/valves to isolate the unit and dial in target flow. Protect from weather; do not submerge. Replace the lamp every 9–12 months for consistent UV dose; clean/inspect the quartz sleeve at each change.
  • Precio regular
    $463.23
    Precio de venta
    $463.23
    Precio regular
    Aqua Ultraviolet – TWIST 25 Watt UV Sterilizer, 2" (White) Overview Compact, high-clarity UV-C sterilizer with a flexible plumbing layout. The TWIST 25W features 2" slip ports and a rotatable union block that lets you “twist” the inlet/outlet orientation to match your plumbing—cutting down on extra elbows and making installs cleaner and faster. Key Features Rotating (TWIST) union block to align inlet/outlet for tight spaces Single 25W low-pressure UV-C lamp for algae/bacteria/protozoa control 2" slip ports support high-flow pond and aquarium loops Clear end cap shows lamp-on status; service-friendly access Weather-resistant housing (non-submersible) for indoor or protected outdoor use Sizing & Flow Guidance Sterilizer (freshwater): ~500–1,200 gal Sterilizer (saltwater): ~150 gal Clarifier (freshwater): up to ~4,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): ~1,200 GPH ≈ 30,000 µW·s/cm² (clarifying) ~800 GPH ≈ 45,000 µW·s/cm² ~600 GPH ≈ 60,000 µW·s/cm² ~480 GPH ≈ 75,000 µW·s/cm² ~400 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: TWIST 25 Watt, 2" Inlet/Outlet, White Lamp: (1) × 25W low-pressure UV-C Electrical: 120 V / 60 Hz; ~0.48 A (typical) Connections: 2" slip (in/out), rotatable union block Dimensions (unit): ~20" × 3-3/4" × 6" Cord Length: ~15 ft Mounting: Wall/stand or supported inline (use appropriate brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included TWIST 25W UV body (White, 2" ports) (1) 25W UV lamp Transformer/power supply Union/slip set Quick start/installation guide Installation Notes Install after mechanical filtration on a pressurized return line. Rotate (twist) the union block to the orientation that best aligns with your plumbing, then solvent-weld and allow full cure. Add unions/valves to isolate the unit and dial-in target flow. Protect from weather; do not submerge. Replace the lamp every 9–12 months for consistent UV dose; clean/inspect the quartz sleeve at each change. Want me to convert this into a single-row Shopify CSV with your standard columns and tags?
  • Precio regular
    $104.72
    Precio de venta
    $104.72
    Precio regular
    Aqua Ultraviolet – SL 200 Watt Replacement Quartz Sleeve with Bushing & Rubber Seal Overview Factory replacement quartz sleeve for the Aqua Ultraviolet SL 200 UV sterilizer. The sleeve isolates the high-wattage lamp from water while maximizing UV-C transmission. Includes the correct end bushing and a new rubber seal for a clean, drip-tight rebuild. Key Features OEM high-clarity quartz sleeve matched to SL 200 End bushing included for proper alignment and support Rubber seal (gasket) restores a reliable, leak-resistant cap interface Quick swap when the old sleeve is stained, etched, or cracked Compatibility Fits Aqua Ultraviolet SL 200 UV sterilizers (two-lamp SL body family) Not interchangeable with Classic-series sleeves or other SL wattages Specifications Part: Quartz sleeve with bushing & rubber seal — SL 200 Materials: UV-transparent fused quartz; engineered bushing; elastomer seal Use: Inside sterilizer housing (component itself is not submersible) What’s Included (1) Quartz sleeve — SL 200 (1) End bushing (1) Rubber seal / gasket Replacement & Care Notes Power OFF and let the unit cool; isolate plumbing and relieve pressure. Remove end cap(s) and lamp(s); carefully withdraw the old sleeve. Clean seating surfaces; lightly lubricate the new seal with silicone-safe lube. Install sleeve and bushing squarely; reassemble hand-tight—do not overtighten. Restore flow and leak-test. Replace UV lamps every 9–12 months and inspect the sleeve at each change.
  • Precio regular
    $924.29
    Precio de venta
    $924.29
    Precio regular
    Aqua Ultraviolet – SL 200 Watt Replacement Lamp Overview OEM 200W UV-C lamp for the Aqua Ultraviolet SL 200 UV sterilizer. Restores full germicidal output for dependable water clarity and pathogen control in high-flow, large-system applications. Key Features Genuine Aqua Ultraviolet 200-watt low-pressure UV-C lamp Direct drop-in fit—no modifications required Stable output for algae, bacteria, and protozoa reduction Typical service life: ~9–12 months of continuous operation Compatibility For Aqua Ultraviolet SL 200 UV sterilizers (matches the SL 200 lamp configuration) Specifications Power: 200 W low-pressure UV-C Peak wavelength: ~254 nm (germicidal) Use: Inside sterilizer housing only (non-submersible component) What’s Included (1) 200W UV-C replacement lamp (bulb only) Replacement Notes Power OFF and allow the unit to cool. Isolate plumbing; open the end cap and carefully remove the old lamp (avoid touching glass). Insert the new lamp fully and reassemble—do not overtighten caps. Restore flow, power ON, and verify illumination (through clear cap if equipped). Replace the lamp every 9–12 months and clean/inspect the quartz sleeve at each change.
  • Precio regular
    $2,270.92
    Precio de venta
    $2,270.92
    Precio regular
    Aqua Ultraviolet – SL 100 Watt UV Sterilizer Overview High-output UV-C sterilizer built for large, high-flow systems. The SL 100 uses a single 100-watt low-pressure UV-C lamp in a streamlined, service-friendly housing—ideal for big ponds, aquaculture, and serious aquarium life-support where dependable water clarity and pathogen reduction are a must. Key Features High-capacity SL body designed for sustained, high-GPH operation Single 100W low-pressure UV-C lamp for powerful germicidal dose Clears green water; reduces free-floating algae, bacteria, and protozoa Weather-resistant, non-submersible housing for indoor or protected outdoor installs Clear end-cap window to confirm lamp-on status at a glance Service-friendly layout for quick lamp and sleeve changes Sizing & Dose Guidance Suitable for large ponds, aquaculture raceways, and big display systems Dial your pump/valves to meet target UV doses (common end-of-lamp-life targets): ~30,000 µW·s/cm² for clarification ~45,000–60,000 µW·s/cm² for general sterilization ~75,000–90,000 µW·s/cm² for tighter pathogen control Use a flow meter or calibrated pump curve to match dose; reduce flow for higher dose. Specifications Model: SL 100 Watt (single-lamp SL series) Lamp: (1) × 100W low-pressure UV-C Electrical: 120V / 60Hz power supply (transformer/ballast) Connections: High-flow union ports (verify size with your plumbing) Finish: Durable polymer housing; black/gray accents (varies by production) Warranty: Limited lifetime on housing; 1-year on electrical and other components What’s Included SL 100 UV sterilizer body (1) 100W UV-C lamp Transformer/ballast power unit Union set (size/style per kit) Quick start/installation guide Installation Notes Install after mechanical filtration on a pressurized return line (not gravity-feed). Add unions and valves to isolate the unit and set flow to your target dose. Mount in a dry, ventilated location; protect power components from spray—do not submerge. Replace the UV lamp every 9–12 months of continuous use; inspect/clean or replace the quartz sleeve as needed. Want this turned into a single-row Shopify CSV with your standard columns and tags?
  • Precio regular
    $117.26
    Precio de venta
    $117.26
    Precio regular
    Aqua Ultraviolet – SL 100 Watt Replacement Quartz Sleeve with Bushing & Rubber Seal Overview Factory replacement quartz sleeve for the Aqua Ultraviolet SL 100 UV sterilizer. The sleeve isolates the lamp from water while maximizing UV-C transmission. Includes the correct end bushing and a new rubber seal for a clean, drip-tight rebuild. Key Features OEM high-clarity quartz sleeve for SL 100 End bushing included for proper fit and alignment Rubber seal (gasket) restores a reliable, leak-resistant cap interface Quick swap when the old sleeve is stained, etched, or cracked Compatibility Fits Aqua Ultraviolet SL 100 UV sterilizers (single-lamp SL body) Not interchangeable with Classic-series sleeves or other SL wattages Specifications Part: Quartz sleeve with bushing & rubber seal — SL 100 Materials: UV-transparent fused quartz; engineered bushing; elastomer seal Use: Inside sterilizer housing (component itself is not submersible) What’s Included (1) Quartz sleeve — SL 100 (1) End bushing (1) Rubber seal / gasket Replacement & Care Notes Power OFF and let the unit cool; isolate plumbing and relieve pressure. Remove end cap and lamp; carefully withdraw the old sleeve. Clean seating surfaces; lightly lubricate the new seal with silicone-safe lube. Install sleeve and bushing squarely; reassemble hand-tight—do not overtighten. Restore flow and leak-test. Replace the UV lamp every 9–12 months and inspect the sleeve at each change.
Go to full site