33043a-03

Aqua Ultraviolet – 8 Watt Quartz Sleeve with Rubber Seal Overview Factory replacement quartz sleeve for Aqua Ultraviolet Classic 8W UV sterilizers. The sleeve isolates the lamp from water while allowing maximum UV-C transmission. Includes a new rubber seal for a drip-tight fit. Key Features OEM quartz sleeve for Classic 8-watt models High-clarity quartz to maintain peak UV output Includes rubber seal (gasket) for secure, leak-resistant installation Fast swap—restore performance when sleeves are stained, etched, or cracked Compatibility Fits Aqua Ultraviolet Classic 8W UV sterilizers (all port sizes; wiper and non-wiper variants) Specifications Item: Quartz Sleeve with Rubber Seal — 8 Watt Material: UV-transparent fused quartz; elastomer seal Fitment: Sized specifically for the Classic 8W body (not interchangeable with other wattages) What’s Included (1) Quartz sleeve – 8W (1) Rubber seal/gasket Replacement & Care Notes Power OFF and isolate the unit; relieve pressure before opening. Inspect the old sleeve—replace if cloudy, etched, or cracked. Clean deposits from the end cap, lightly lubricate the new seal with silicone-safe lube, and seat the sleeve squarely. Hand-tighten only; do not overtighten end hardware. Replace lamps annually (≈9–12 months run time) and sleeves as needed for maximum UV dose.

Aqua Ultraviolet – 57 Watt Classic UV Sterilizer, 3/4" (White) Overview A proven, mid-high output UV-C sterilizer for ponds and aquariums. The Classic 57W with 3/4" ports delivers strong water clarity and pathogen reduction in a service-friendly housing—ideal for medium–large ponds, large displays, and reef life-support loops. Key Features Classic housing with 3/4" inlet/outlet for easy inline plumbing Single low-pressure 57W UV-C lamp targets algae, bacteria, and protozoa Weather-resistant (non-submersible) body for indoor or protected outdoor installs Clear end cap shows lamp-on status; quick access for lamp/sleeve changes Optional Wiper variant available (not recommended for saltwater use) Sizing & Flow Guidance Sterilizer (freshwater): ~1,800–3,500 gal Sterilizer (saltwater): ~500–700 gal Clarifier (freshwater): up to ~8,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): ~3,600 GPH ≈ 30,000 µW·s/cm² (clarifying) ~2,400 GPH ≈ 45,000 µW·s/cm² ~1,800 GPH ≈ 60,000 µW·s/cm² ~1,440 GPH ≈ 75,000 µW·s/cm² ~1,200 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic 57 Watt, 3/4" Inlet/Outlet, White (No Wiper) Lamp: (1) × 57W low-pressure UV-C Electrical: 120 V / 60 Hz Connections: 3/4" (barb or slip style per kit) Dimensions (unit): ~23" × 3-3/4" × 6" Cord Length: ~15 ft Mounting: Wall/stand (use suitable brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 57W UV body (White, 3/4" ports) (1) 57W UV lamp Inline power supply Union/fitting set (3/4") Quick start/installation guide Installation Notes Plumb after mechanical filtration on a pressure line; avoid gravity-feed. Add unions/valves to set/service flow to your target dose. Protect from weather; do not submerge. Replace the lamp every ~9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – 57 Watt Classic UV Sterilizer, 3/4" (Black) with Wiper Overview A workhorse UV-C sterilizer for medium–large ponds and serious aquarium systems. This Classic 57W model with 3/4" ports adds a manual wiper to keep the quartz sleeve clear between services—great for maintaining consistent UV output in high-load systems. Key Features Classic housing with 3/4" inlet/outlet for easy inline plumbing Single low-pressure 57W UV-C lamp for algae, bacteria, and protozoa control Integrated manual wiper helps maintain sleeve clarity and stable performance Weather-resistant (non-submersible) body for indoor or protected outdoor installs Clear end cap shows lamp-on status; service-friendly layout Note: Wipers are not recommended for saltwater use; using a wiper on saltwater can void the wiper warranty. Many marine installs choose the non-wiper version and clean the sleeve during lamp changes. Sizing & Flow Guidance Sterilizer (freshwater): ~1,800–3,500 gal Sterilizer (saltwater): ~500–700 gal Clarifier (freshwater): up to ~8,000 gal (with 50–75% plant coverage) Typical UV-dose flow targets (EOL): ~3,600 GPH ≈ 30,000 µW·s/cm² (clarifying) ~2,400 GPH ≈ 45,000 µW·s/cm² ~1,800 GPH ≈ 60,000 µW·s/cm² ~1,440 GPH ≈ 75,000 µW·s/cm² ~1,200 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic 57 Watt, 3/4" Inlet/Outlet, Black, with Wiper Lamp: (1) × 57W low-pressure UV-C Connections: 3/4" (barb or slip style per kit) Dimensions (unit): ~23" × 3-3/4" × 6" Dimensions with Wiper: ~25" × 3-3/4" × 6" Wiper clearance: 12" Electrical: 120 V / 60 Hz Cord Length: ~15 ft Mounting: Wall/stand (use suitable brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components (wiper excluded from saltwater coverage) What’s Included Classic 57W UV body (Black, 3/4" ports) with manual wiper (1) 57W UV lamp Inline power supply Union/fitting set (3/4") Quick start/installation guide Installation Notes Plumb after mechanical filtration on a pressure line; avoid gravity-feed. Use unions/valves to service and to tune flow to your target dose. Operate the wiper with the lamp off and pressure relieved. Protect from weather; do not submerge. Replace the lamp every ~9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – 57 Watt Classic UV Sterilizer, 2" (White) Overview A proven, mid-high output UV-C sterilizer for ponds and aquariums. The Classic 57W with 2" slip ports delivers strong water-clarity and pathogen reduction in a service-friendly housing—ideal for medium–large ponds, large displays, and reef life-support loops. Key Features Classic housing with 2" slip inlet/outlet for high-flow plumbing Single low-pressure 57W UV-C lamp for algae/bacteria/protozoa control Weather-resistant (non-submersible) body for indoor or protected outdoor installs Clear end cap shows lamp-on status; quick access for lamp/sleeve changes Optional Wiper variant available (not recommended for saltwater use) Sizing & Flow Guidance Sterilizer (freshwater): ~1,800–3,500 gal Sterilizer (saltwater): ~500–700 gal Clarifier (freshwater): up to ~8,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): ~3,600 GPH ≈ 30,000 µW·s/cm² (clarifying) ~2,400 GPH ≈ 45,000 µW·s/cm² ~1,800 GPH ≈ 60,000 µW·s/cm² ~1,440 GPH ≈ 75,000 µW·s/cm² ~1,200 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic 57 Watt, 2" Inlet/Outlet, White (No Wiper) MPN: A00057 Lamp: (1) × 57W low-pressure UV-C Electrical: 120 V / 60 Hz Connections: 2" slip (in/out) Dimensions (unit): ~23" × 3-3/4" × 6" Cord Length: ~15 ft Mounting: Wall/stand (use suitable brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 57W UV body (White, 2" ports) (1) 57W UV lamp Inline power supply Union/fitting set (2" slip) Quick start/installation guide Installation Notes Plumb after mechanical filtration on a pressure line; avoid gravity-feed. Add unions/valves to set/service flow to your target dose. Protect from weather; do not submerge. Replace the lamp every ~9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – 57 Watt Classic UV Sterilizer, 2" (Black) with Wiper Overview A workhorse UV-C sterilizer for medium–large ponds and serious aquarium systems. This Classic 57W model with 2" slip ports adds a manual wiper to keep the quartz sleeve clear between services—great for maintaining consistent UV output in high-load systems. Key Features Classic housing with 2" slip inlet/outlet for high-flow plumbing Single low-pressure 57W UV-C lamp for algae, bacteria, and protozoa control Integrated manual wiper helps maintain sleeve clarity and stable performance Weather-resistant (non-submersible) body for indoor or protected outdoor installs Clear end cap shows lamp-on status; service-friendly layout Note: Wipers are not recommended for saltwater use; using a wiper on saltwater can void the wiper warranty. Many marine installs choose the non-wiper version and clean the sleeve during lamp changes. Sizing & Flow Guidance Sterilizer (freshwater): ~1,800–3,500 gal Sterilizer (saltwater): ~500–700 gal Clarifier (freshwater): up to ~8,000 gal (with 50–75% plant coverage) Typical UV-dose flow targets (EOL): ~3,600 GPH ≈ 30,000 µW·s/cm² (clarifying) ~2,400 GPH ≈ 45,000 µW·s/cm² ~1,800 GPH ≈ 60,000 µW·s/cm² ~1,440 GPH ≈ 75,000 µW·s/cm² ~1,200 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic 57 Watt, 2" Inlet/Outlet, Black, with Wiper Lamp: (1) × 57W low-pressure UV-C Connections: 2" slip (in/out) Dimensions (unit): ~23" × 3-3/4" × 6" Dimensions with Wiper: ~25" × 3-3/4" × 6" Wiper clearance: 12" Cord Length: ~15 ft Mounting: Wall/stand (use suitable brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components (wiper excluded from saltwater coverage) What’s Included Classic 57W UV body (Black, 2" ports) with manual wiper (1) 57W UV lamp Inline power supply Union/fitting set (2" slip) Quick start/installation guide Installation Notes Plumb after mechanical filtration on a pressure line; avoid gravity-feed. Use unions/valves to service and to tune flow to your target dose. Operate the wiper with the lamp off and pressure relieved. Protect from weather; do not submerge. Replace the lamp every ~9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – 40 Watt Replacement Raw Transformer / Ballast Overview OEM replacement raw transformer/ballast for Aqua Ultraviolet 40W UV sterilizers. Restores proper lamp ignition and operating current when a power supply has failed or aged out. Key Features Genuine replacement power component for 40-watt Aqua UV lamps Delivers correct start/operating current to maintain UV output “Raw” component—ideal for service techs and in-house repairs Compatible with wiper and non-wiper models Compatibility Aqua Ultraviolet Classic 40W UV sterilizers (all port sizes) Not for other wattages (15W/25W/57W/80W/etc.) Specifications Type: Low-pressure UV-C lamp transformer/ballast (40W) Input: 120V AC, 60Hz (typical) Output: Matched to Aqua UV 40W low-pressure UV-C lamp Form factor: Raw component (no housing) Leads: Pigtail wiring (line/neutral/ground and lamp leads) What’s Included (1) 40W raw transformer/ballast Installation & Safety Notes Disconnect power and isolate the unit before service. Mount in a dry, ventilated area—do not submerge or expose to spray. Follow the factory wiring diagram; match line/neutral/ground correctly. Use proper connectors/heat-shrink; strain-relieve all leads. After replacement, verify lamp strike and amperage; replace lamps/sleeve as needed.

Aqua Ultraviolet – 40 Watt Classic UV Sterilizer, 3/4" (Black) with Wiper Overview Mid-size, high-clarity UV-C sterilizer for ponds and aquariums. This Classic 40W model uses 3/4" ports and adds a manual wiper to keep the quartz sleeve clean between services—ideal for medium ponds, larger displays, and reef life-support polishing loops. Key Features Classic housing with 3/4" inlet/outlet for easy inline plumbing Single low-pressure 40W UV-C lamp for algae/bacteria/protozoa control Integrated manual wiper helps maintain sleeve clarity and consistent UV output Weather-resistant (non-submersible) body for indoor or protected outdoor installs Clear end cap shows lamp-on status; quick access for lamp/sleeve changes Note: Wipers are not recommended for saltwater use; using a wiper on saltwater can void the wiper warranty. Many marine installs choose the non-wiper variant and clean the sleeve during lamp changes. Sizing & Flow Guidance Sterilizer (freshwater): ~1,200–2,000 gal Sterilizer (saltwater): ~325 gal Clarifier (freshwater): up to ~6,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): ~2,900 GPH ≈ 30,000 µW·s/cm² (clarifying) ~1,930 GPH ≈ 45,000 µW·s/cm² ~1,450 GPH ≈ 60,000 µW·s/cm² ~1,160 GPH ≈ 75,000 µW·s/cm² ~967 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic 40 Watt, 3/4" Inlet/Outlet, Black, with Wiper Lamp: (1) × 40W low-pressure UV-C Electrical: 120 V / 60 Hz Connections: 3/4" (barb or slip style per kit) Wiper clearance: 12" Cord Length: ~15 ft Mounting: Wall/stand (use suitable brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components (wiper excluded from saltwater coverage) What’s Included Classic 40W UV body (Black, 3/4" ports) with manual wiper (1) 40W UV lamp Inline power supply Union/fitting set (3/4") Quick start/installation guide Installation Notes Plumb after mechanical filtration on a pressure line; avoid gravity-feed. Use unions/valves to set and service flow to your target dose. Operate the wiper with the lamp off and pressure relieved. Protect from weather; do not submerge. Replace the lamp every ~9–12 months of continuous use to maintain dose.

Overview FRESHWATER ONLY – The Aqua Ultraviolet 40 Watt UV Sterilizer with Wiper is the premium solution for both sterilization and clarification in freshwater ponds. Ideal for ponds ranging from 1,200 to 2,000 gallons when used as a sterilizer and up to 6,000 gallons when used as a clarifier (with 50% to 75% plant coverage), this unit creates a healthier ecosystem by controlling harmful bacteria and clarifying green water. Enjoy industry-leading lamp life and reliable performance with easy installation and maintenance. Key Features Dual Functionality: Sterilizer: Controls harmful bacteria in ponds (1,200–2,000 gallons). Clarifier: Clears green water in ponds up to 6,000 gallons with heavy plant coverage. Premium Design with Wiper: Integrated wiper ensures continuous cleaning of the quartz sleeve for optimal UV transmission. Industry-Leading Lamp Life: 14-month lamp life – the longest in the industry. Complete Out-of-Box Use: Includes transformer, lamp, and quartz sleeve for immediate setup. Robust Construction & Warranty: Lifetime manufacturer’s warranty on the housing, 90 days on the transformer, and a 14-month prorated warranty on the lamp. Optimized Flow Rates: Maximum flow rate of 2,900 GPH when used as a sterilizer and 3,000 GPH as a clarifier.

Aqua Ultraviolet – 25 Watt Classic UV Sterilizer, 2" (Black) with Wiper Overview Reliable, compact UV-C sterilizer for ponds and aquariums. This Classic 25W model with 2" slip ports adds a manual wiper to help keep the quartz sleeve clear between services—great for polishing loops, QT systems, and modest displays. Key Features Classic housing with 2" slip inlet/outlet for easy high-flow plumbing Single low-pressure 25W UV-C lamp for algae/bacteria/protozoa control Integrated manual wiper helps maintain sleeve clarity and consistent UV output Weather-resistant (non-submersible) body for indoor or protected outdoor installs Clear end cap shows lamp-on status; quick access for lamp/sleeve changes Note: Wipers are not recommended for saltwater use; using a wiper on saltwater can void the wiper warranty. Many marine installs choose the non-wiper variant and clean the sleeve during lamp changes. Sizing & Flow Guidance Sterilizer (freshwater): ~500–1,200 gal Sterilizer (saltwater): ~150 gal Clarifier (freshwater): up to ~4,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): ~1,200 GPH ≈ 30,000 µW·s/cm² (max clarifying flow) ~800 GPH ≈ 45,000 µW·s/cm² ~600 GPH ≈ 60,000 µW·s/cm² ~480 GPH ≈ 75,000 µW·s/cm² ~400 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic 25 Watt, 2" Inlet/Outlet, Black, with Wiper Lamp: (1) × 25W low-pressure UV-C Electrical: 120 V / 60 Hz; ~0.48 A Connections: 2" slip (in/out) Dimensions (unit): 20" × 3-3/4" × 6" Dimensions with Wiper: 22-3/4" × 3-3/4" × 6" Wiper clearance: 12" Cord Length: ~15 ft Mounting: Wall/stand (use suitable brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components (wiper excluded from saltwater coverage) What’s Included Classic 25W UV body (Black, 2" ports) with manual wiper (1) 25W UV lamp Inline power supply Union/fitting set (2" slip) Quick start/installation guide Installation Notes Plumb after mechanical filtration on a pressure line; avoid gravity-feed. Add unions/valves for service and to set flow. Operate the wiper with the lamp off; relieve pressure before wiping. Protect from weather; do not submerge. Replace the lamp every ~9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – 25 Watt Quartz Sleeve w/ Rubber Seal Overview Factory replacement quartz sleeve for Aqua Ultraviolet Classic 25W UV sterilizers. The sleeve protects the lamp from water while allowing maximum UV-C transmission. Includes a new rubber seal for a drip-tight fit. Key Features OEM quartz sleeve for Classic 25-watt models High-clarity quartz to maintain peak UV output Includes rubber seal (gasket) for secure, leak-resistant installation Fast swap—restore performance when sleeves are stained, etched, or cracked Compatibility Fits Aqua Ultraviolet Classic 25W UV sterilizers (all port sizes; wiper and non-wiper variants) Specifications Item: Quartz Sleeve with Rubber Seal — 25 Watt Material: UV-transparent fused quartz; elastomer seal Fitment: Sized specifically for the Classic 25W body (not interchangeable with other wattages) What’s Included (1) Quartz sleeve – 25W (1) Rubber seal/gasket Replacement & Care Notes Power OFF and isolate the unit; relieve pressure before opening. Inspect the old sleeve—replace if cloudy, etched, or cracked. Clean deposits from the end cap, lightly lubricate the new seal with silicone-safe lube, and seat the sleeve squarely. Hand-tighten only; do not overtighten end hardware. Replace lamps annually (≈9–12 months run time) and sleeves as needed for maximum UV dose.

Aqua Ultraviolet – 25 Watt Classic UV Sterilizer, 3/4" (White) Overview Reliable, compact UV-C sterilizer for ponds and aquariums. The Classic 25W with 3/4" ports delivers proven water clarity and pathogen reduction in a service-friendly housing—great for polishing loops, QT systems, and modest displays. Key Features Classic housing with 3/4" inlet/outlet for easy inline plumbing Single low-pressure 25W UV-C lamp for algae/bacteria/protozoa control Weather-resistant (non-submersible) body for indoor or protected outdoor installs Clear end cap shows lamp-on status; quick access for lamp/sleeve changes Optional “Wiper” variant available (not recommended for saltwater use) Sizing & Flow Guidance Sterilizer (freshwater): ~500–1,200 gal Sterilizer (saltwater): ~150 gal Clarifier (freshwater): up to ~4,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): ~1,200 GPH ≈ 30,000 µW·s/cm² (max clarifying flow) ~800 GPH ≈ 45,000 µW·s/cm² ~600 GPH ≈ 60,000 µW·s/cm² ~480 GPH ≈ 75,000 µW·s/cm² ~400 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic 25 Watt, 3/4" Inlet/Outlet, White (No Wiper) Lamp: (1) × 25W low-pressure UV-C Electrical: 120 V / 60 Hz; ~0.48 A Connections: 3/4" (barb or slip style per kit) Dimensions (unit): 20" × 3-3/4" × 6" Cord Length: ~15 ft Mounting: Wall/stand (use suitable brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 25W UV body (White, 3/4" ports) (1) 25W UV lamp Inline power supply Union/fitting set (3/4") Quick start/installation guide Installation Notes Plumb after mechanical filtration on a pressure line; avoid gravity-feed. Add unions/valves for service and to set flow. Protect from weather; do not submerge. Replace the lamp every ~9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – 25 Watt Classic UV Sterilizer, 2" (White) Overview Reliable, compact UV-C sterilizer for ponds and aquariums. The Classic 25W with 2" slip ports delivers proven water clarity and pathogen reduction in a service-friendly housing—great for polishing loops, QT systems, and modest displays. Key Features Classic housing with 2" slip inlet/outlet for easy high-flow plumbing Single low-pressure 25W UV-C lamp for algae/bacteria/protozoa control Weather-resistant (non-submersible) body for indoor or protected outdoor installs Clear end cap shows lamp-on status; quick access for lamp/sleeve changes Optional “Wiper” variant available (not recommended for saltwater use) Sizing & Flow Guidance Sterilizer (freshwater): ~500–1,200 gal Sterilizer (saltwater): ~150 gal Clarifier (freshwater): up to ~4,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): ~1,200 GPH ≈ 30,000 µW·s/cm² (max clarifying flow) ~800 GPH ≈ 45,000 µW·s/cm² ~600 GPH ≈ 60,000 µW·s/cm² ~480 GPH ≈ 75,000 µW·s/cm² ~400 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic 25 Watt, 2" Inlet/Outlet, White (No Wiper) MPN: A00025 Lamp: (1) × 25W low-pressure UV-C Electrical: 120 V / 60 Hz; ~0.48 A Connections: 2" slip (in/out) Dimensions (unit): 20" × 3-3/4" × 6" Cord Length: ~15 ft Mounting: Wall/stand (use suitable brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 25W UV body (White, 2" ports) (1) 25W UV lamp Inline power supply Union/fitting set (2" slip) Quick start/installation guide Installation Notes Plumb after mechanical filtration on a pressure line; avoid gravity-feed. Add unions/valves for service and to set flow. Protect from weather; do not submerge. Replace the lamp every ~9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – 25 Watt Classic UV Sterilizer, 2" (Black) Overview Reliable, compact UV-C sterilizer for ponds and aquariums. The Classic 25W with 2" slip ports delivers proven water-clarity and pathogen reduction in a service-friendly housing—great for polishing loops, QT systems, and modest displays. Key Features Classic housing with 2" slip inlet/outlet for easy high-flow plumbing Single low-pressure 25W UV-C lamp for algae/bacteria/protozoa control Weather-resistant (non-submersible) body for indoor or protected outdoor installs Clear end cap shows lamp-on status; quick access for lamp/sleeve changes Optional “Wiper” variant available (not recommended for saltwater use) Sizing & Flow Guidance Sterilizer (freshwater): ~500–1,200 gal Sterilizer (saltwater): ~150 gal Clarifier (freshwater): up to ~4,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): ~1,200 GPH ≈ 30,000 µW·s/cm² (max clarifying flow) ~800 GPH ≈ 45,000 µW·s/cm² ~600 GPH ≈ 60,000 µW·s/cm² ~480 GPH ≈ 75,000 µW·s/cm² ~400 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic 25 Watt, 2" Inlet/Outlet, Black (No Wiper) MPN: A00028 UPC: 617750000282 Lamp: (1) × 25W low-pressure UV-C Electrical: 120 V / 60 Hz; ~0.48 A Connections: 2" slip (in/out) Dimensions (unit): 20" × 3-3/4" × 6" Cord Length: ~15 ft Mounting: Wall/stand (use suitable brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 25W UV body (Black, 2" ports) (1) 25W UV lamp Inline power supply Union/fitting set (2" slip) Quick start/installation guide Installation Notes Plumb after mechanical filtration on a pressure line; avoid gravity-feed. Add unions/valves for service and to set flow. Protect from weather; do not submerge. Replace the lamp every ~9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – 160 Watt Classic UV Sterilizer, 2" (White) w/ NEMA Transformer Overview High-capacity UV-C sterilizer for large ponds, aquaculture, and serious aquarium life-support. The Classic 160W with 2" slip ports and NEMA transformer (120V/60Hz) delivers robust water clarification and pathogen reduction with four 40-watt lamps in a service-friendly housing. Key Features Heavy-duty Classic body with 2" slip inlet/outlet for high-flow plumbing Quad-lamp (4 × 40W) design for strong UV dose and clear water Clears green water; reduces algae, bacteria, and protozoa load Weather-resistant (non-submersible) for indoor or protected outdoor installs Remote NEMA transformer for reliable, easy-service power management Sizing & Flow Guidance Sterilizer (freshwater): ~6,000–8,500 gal Sterilizer (saltwater): ~1,200 gal Clarifier (freshwater): up to ~16,000 gal (with 50–75% plant coverage) Typical UV-dose flow targets (EOL): ~5,400 GPH ≈ 30,000 µW·s/cm² (max clarifying flow) ~3,600 GPH ≈ 45,000 µW·s/cm² ~2,700 GPH ≈ 60,000 µW·s/cm² ~2,160 GPH ≈ 75,000 µW·s/cm² For tighter pathogen control, throttle toward the higher-dose flow targets. Use valves/unions to fine-tune and service. Specifications Model: Classic 160 Watt, 2" Inlet/Outlet, White, w/ NEMA Transformer MPN: A00160 UPC: 617750001609 Lamps: 4 × 40W low-pressure UV-C Electrical: 120V/60Hz, approx. 1.7 A (total) Connections: 2" slip (in/out) Dimensions (2" unit): 36-7/8" × 8-5/8" × 17-1/2" Cord Length: ~15 ft Mounting: Wall/stand (use appropriate brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 160W UV body (White, 2" ports) (4) 40W UV lamps NEMA transformer (remote power supply) Union/fitting set (2" slip) Quick start/installation guide Installation Notes Install after mechanical filtration on a pressure line; avoid gravity-feed. Use unions/valves to isolate the unit and set flow to target dose. Protect from weather; do not submerge. Replace lamps annually (≈9–12 months run time) to maintain UV output.

Aqua Ultraviolet – 15 Watt Quartz Sleeve with Rubber Seal Overview Factory replacement quartz sleeve for Aqua Ultraviolet Classic 15W UV sterilizers. The sleeve isolates the lamp from water while allowing maximum UV-C transmission. Includes a new rubber seal for a drip-tight fit. Key Features OEM quartz sleeve for Classic 15-watt models High-clarity quartz for optimal UV output Includes rubber seal (gasket) for secure, leak-resistant install Fast swap—restore performance when sleeves are stained, etched, or cracked Compatibility Fits Aqua Ultraviolet Classic 15W UV sterilizers (all port sizes; wiper and non-wiper variants) Specifications Item: Quartz Sleeve with Rubber Seal — 15 Watt Length: ~15" (sleeve) MPN: A10015 UPC: 617750100159 Material: UV-transparent fused quartz; elastomer seal What’s Included (1) Quartz sleeve – 15W (1) Rubber seal/gasket Replacement & Care Notes Power OFF and isolate the unit; relieve pressure before opening. Inspect the old sleeve—replace if cloudy, etched, or cracked. Clean any deposits in the end cap, lightly lubricate the new seal with silicone-safe lube, and seat the sleeve squarely. Hand-tighten only; do not overtighten end hardware. Replace lamps annually (≈9–12 months run time) and sleeves as needed for maximum UV dose.

Aqua Ultraviolet – 15 Watt Classic UV Sterilizer, 3/4" (Black) with Wiper Overview Compact, durable UV-C sterilizer for ponds and aquariums. This Classic 15W model uses 3/4" ports and adds a manual wiper to help keep the quartz sleeve clear between services—great for polishing loops, QT systems, and modest displays. Key Features Classic housing with 3/4" inlet/outlet for easy inline plumbing Single low-pressure 15W UV-C lamp for algae/bacteria/protozoa control Manual wiper helps maintain sleeve clarity and consistent UV output Weather-resistant (non-submersible) for indoor or protected outdoor installs Clear end cap shows lamp-on status; quick access for lamp/sleeve changes Note: Wipers are not recommended for saltwater use; using a wiper on saltwater can void the wiper warranty. Many marine installs choose the non-wiper variant and clean the sleeve during lamp changes. Sizing & Flow Guidance Sterilizer (freshwater): ~200–500 gal Sterilizer (saltwater): ~75 gal Clarifier (freshwater): up to ~2,000 gal Target UV-dose flows (EOL): ~700 GPH ≈ 30,000 µW·s/cm² ~466 GPH ≈ 45,000 µW·s/cm² ~350 GPH ≈ 60,000 µW·s/cm² ~280 GPH ≈ 75,000 µW·s/cm² ~233 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic 15 Watt, 3/4" Inlet/Outlet, Black, with Wiper MPN: A00033 UPC: 617750000336 Lamp: (1) × 15W low-pressure UV-C Electrical: 120 V / 60 Hz; 0.48 A (approx.) Connections: 3/4" (barb or slip style per kit) Dimensions (unit): 16" × 3-3/4" × 6" Dimensions with Wiper: 17-7/8" × 3-3/4" × 6" Wiper clearance: 12" Cord Length: ~15 ft Mounting: Wall/stand (use suitable brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components (wiper excluded from saltwater coverage) What’s Included Classic 15W UV body (Black, 3/4" ports) with manual wiper (1) 15W UV lamp Inline power supply Union/fitting set (3/4") Quick start/installation guide Installation Notes Plumb after mechanical filtration on a pressure line; avoid gravity-feed. Add unions/valves for service and to set flow. Operate the wiper with the lamp off; relieve pressure before wiping. Protect from weather; do not submerge. Replace the lamp every ~9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – 15 Watt Classic UV Sterilizer, 2" (Black) with Wiper Overview Compact, durable UV-C sterilizer for ponds and aquariums. This Classic 15W model with 2" slip ports adds a built-in manual wiper to help keep the quartz sleeve clear between services—great for polishing loops, QT systems, and modest displays. Key Features Classic housing with 2" slip inlet/outlet for easy plumbing in high-flow systems Single low-pressure 15W UV-C lamp for algae/bacteria/protozoa control Integrated manual wiper helps maintain sleeve clarity and UV performance Weather-resistant (non-submersible) body for indoor or protected outdoor installs Clear end cap shows lamp-on status; quick access for lamp/sleeve changes Note: Aqua Ultraviolet does not recommend wipers for saltwater use; doing so can void the wiper warranty. For marine systems, many installers choose the non-wiper variant and clean the sleeve during lamp changes. Sizing & Flow Guidance Sterilizer (freshwater): ~200–500 gal Sterilizer (saltwater): ~75 gal Clarifier (freshwater): up to ~2,000 gal Target UV-dose flows (EOL): ~700 GPH ≈ 30,000 µW·s/cm² (clarifying) ~466 GPH ≈ 45,000 µW·s/cm² ~350 GPH ≈ 60,000 µW·s/cm² ~280 GPH ≈ 75,000 µW·s/cm² ~233 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic 15 Watt, 2" Inlet/Outlet, Black, with Wiper MPN: A00034 Lamp: (1) × 15W low-pressure UV-C Electrical: 120 V / 60 Hz; 0.48 A (approx.) Connections: 2" slip (in/out) Dimensions (unit): 16" × 3-3/4" × 6" Dimensions with Wiper: 17-7/8" × 3-3/4" × 6" Wiper clearance: 12" Cord Length: ~15 ft Mounting: Wall/stand (use suitable brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components (wiper excluded from saltwater coverage) What’s Included Classic 15W UV body (Black, 2" ports) with manual wiper (1) 15W UV lamp Inline power supply Union/fitting set (2" slip) Quick start/installation guide Installation Notes Install after mechanical filtration on a pressure line; avoid gravity-feed. Use unions/valves to set/service flow and to isolate the unit. Operate the wiper with the lamp off; open/close valves as needed to relieve pressure first. Protect from weather; do not submerge. Replace lamp every ~9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – 15 Watt Classic UV Sterilizer, 2" (Black) Overview Compact, durable UV-C sterilizer for ponds and aquariums. The Classic 15W with 2" slip ports delivers proven water-clarity and pathogen reduction in a small footprint—great for polishing loops, quarantine systems, and modest displays. Key Features Classic housing with 2" slip inlet/outlet for easy plumbing into high-flow systems Single low-pressure 15W UV-C lamp for effective algae/bacteria/protozoa control Weather-resistant (non-submersible) for indoor or protected outdoor installs Quick service access; clear end cap shows lamp-on status Optional “Wiper” variant available (not recommended for saltwater use) Sizing & Flow Guidance Sterilizer (freshwater): ~200–500 gal Sterilizer (saltwater): ~75 gal Clarifier (freshwater): up to ~2,000 gal Typical UV-dose flow targets (EOL): ~700 GPH ≈ 30,000 µW·s/cm² (clarifying) ~466 GPH ≈ 45,000 µW·s/cm² ~350 GPH ≈ 60,000 µW·s/cm² ~233 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) For stronger sterilization, throttle flow toward the higher-dose targets. Specifications Model: Classic 15 Watt, 2" Inlet/Outlet, Black (No Wiper) MPN: A00031 Lamp: (1) × 15W low-pressure UV-C Electrical: 120 V / 60 Hz; 0.48 A (approx.) Connections: 2" slip (in/out) Dimensions (unit): 16" × 3.75" × 6" Cord Length: ~15 ft Mounting: Wall/stand (use suitable brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 15W UV body (Black, 2" ports) (1) 15W UV lamp Inline power supply Union/fitting set (2" slip) Quick start/installation guide Installation Notes Install after mechanical filtration on a pressure line; avoid gravity-feed. Use unions/valves to set and service flow. Protect from weather; do not submerge. Replace lamp every ~9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – 114 Watt Classic UV Sterilizer, 2" (White) Overview A high-capacity UV sterilizer for serious pond and aquarium systems. The Classic 114W (2" ports) uses dual 57-watt lamps and a reflective internal chamber to deliver strong UV-C performance for water clarity and pathogen control—ideal for large freshwater ponds or sizeable saltwater/reef life-support loops. Key Features Heavy-duty Classic housing with 2" slip ports for high-flow plumbing Dual-lamp design (2 × 57W) with separate inline power supplies Clears green water and reduces algae, bacteria, and protozoa load Weather-resistant, non-submersible body for indoor or protected outdoor installs Service-friendly layout; optional manual wiper available on the “Wiper” variant Sizing & Flow Guidance Sterilizer (freshwater): up to ~2,200–4,400 gal Sterilizer (saltwater): up to ~700 gal Clarifier (freshwater): up to ~9,500 gal (with 50–75% plant coverage) Typical max flow (sterilizer): ~3,900 GPH target for ~30,000 μW·s/cm² at end-of-lamp life For tighter pathogen control (higher UV dose), reduce flow; for simple water clarification, higher flow is acceptable. Match pump and head-loss accordingly. Specifications Model: Classic 114 Watt, 2" Inlet/Outlet, White (No Wiper) MPN: A00114 Lamps: (2) × 57W low-pressure UV-C Electrical: 120V/60Hz, two inline transformers; ~0.85A total draw Connections: 2" slip (in/out) Dimensions (unit): 20" × 3-3/4" × 16-1/2" Cord Length: ~15 ft Mounting: Wall/stand (use appropriate brackets/anchors) Warranty: Limited lifetime on housing; 1 year on other components (lamps/transformers excluded from lifetime) What’s Included Classic 114W UV body (White, 2" ports) (2) 57W UV lamps (2) inline power supplies Union/fitting set (2" slip) Quick start/installation guide Installation Notes Install after mechanical filtration on a pressure side; do not gravity-feed. Use unions/valves for service and to fine-tune flow. For marine systems, many pros skip the wiper variant; manual sleeve cleaning during lamp changes works well. Replace lamps annually (≈9–12 months run time) for consistent UV dose. Protect from direct weather; unit is weather-resistant, not submersible.

Aqua Ultraviolet – UV Mounting Bracket (Single) Overview Secure your Aqua Ultraviolet UV sterilizer to a wall or stand with this factory mounting bracket. The integrated grip-hold clip keeps the sterilizer body from shifting or twisting, making installs tidy and serviceable. Key Features Purpose-built for Aqua Ultraviolet UV sterilizers Grip-hold clip helps prevent movement and vibration Sold individually (most single-lamp units use 2 brackets) Simple, tool-light installation for clean, professional mounting Compatibility Fits most Aqua Ultraviolet units with a 2" body (e.g., common single-lamp Classic bodies). For multi-lamp or larger/heavier models, use additional brackets as needed. Specifications Item: UV Mounting Bracket (Single) MPN: A40124 UPC: 617750401249 Finish/Material: Durable molded bracket with integrated grip clip Use: Indoor/aquarium, pond, and life-support equipment rooms What’s Included (1) Aqua Ultraviolet UV Mounting Bracket Installation Notes Position the bracket on a flat, load-bearing surface. Mark and fasten using appropriate anchors/screws for your substrate (not included). Snap the UV body into the grip-hold clip. If supporting a vertical install or long runs of plumbing, use a second bracket for proper support.