33043a-03

Aqua Ultraviolet – PART: Ultima Filter Union O-Ring, 1.5" Overview OEM replacement O-ring for Aqua Ultraviolet Ultima series filter unions sized 1.5". Restores a drip-tight seal between union halves to stop weeps and air draw. Key Features Genuine replacement O-ring for 1.5" Ultima filter unions Resilient elastomer for reliable, long-lasting sealing Seats easily; compatible with silicone-safe lubricants Fixes leaks caused by flattened, cracked, or missing seals Compatibility Aqua Ultraviolet Ultima / Ultima II filters using 1.5" union connections Verify union size before ordering (does not fit 2" or other sizes) Specifications Part Type: Union O-ring Size: 1.5" union (nominal) Material: Durable elastomer (black) Use: External, wet-location plumbing (non-submersible component) What’s Included (1) 1.5" Ultima union O-ring Installation Notes Shut off pump and relieve pressure. Separate the union and remove the old O-ring; clean groove and mating faces. Lightly coat the new O-ring with silicone-based lubricant (no petroleum). Seat evenly in the groove; reassemble the union hand-tight, then snug. Pressurize and leak-test.

Aqua Ultraviolet – PART: Transformer Cap (Black) Overview OEM replacement black transformer cap for Aqua Ultraviolet UV sterilizers. Restores a clean, protected termination for the power supply housing, keeping wiring covered and moisture-resistant. Key Features Genuine Aqua Ultraviolet replacement cap Protects internal wiring and terminals from dust and splashes Integrated strain relief opening for safe cord routing Snug, service-friendly fit for quick swaps Works with wiper and non-wiper units Compatibility Designed for Aqua Ultraviolet transformer/power supply housings used on Classic, SL, and Advantage series (match to your transformer style before ordering). Specifications Color: Black Part Type: Transformer end cap / cover Material: Durable, UV- and heat-resistant polymer Use: Dry location (non-submersible component) What’s Included (1) Transformer Cap — Black Installation Notes Disconnect power before service. Verify wiring connections inside the transformer housing. Route the cord through the cap’s strain relief, seat the cap fully, and secure per factory method. Keep the transformer in a dry, ventilated area; do not submerge.

Aqua Ultraviolet – PART: Lamp End Connector, 4 Holes Overview OEM replacement lamp end connector with 4 holes for Aqua Ultraviolet UV sterilizers. This connector secures and insulates the four lamp leads at the end cap, ensuring a solid electrical connection and safe, reliable operation. Key Features Genuine Aqua Ultraviolet replacement part 4-hole design for standard low-pressure UV lamp lead routing Heat- and UV-resistant body for long service life Restores proper contact to fix flicker, intermittent starts, or loose leads Works with both wiper and non-wiper units Compatibility Aqua Ultraviolet Classic and SL series that use the 4-lead lamp harness Fits most wattages that terminate with a 4-lead end (check your unit before ordering) Specifications Part Type: Lamp end connector / lead block Interface: 4-hole pass-through for lamp wires Material: Heat-resistant polymer/ceramic with insulating properties Color: White or off-white (varies by production) Use: Dry location inside end-cap assembly (non-submersible component) What’s Included (1) Lamp End Connector, 4 Holes Installation Notes Disconnect power and allow the unit to cool before servicing. Open the end-cap; note existing wire order/position. Transfer each lead into the new connector—ensure firm, fully seated contact. Reassemble the end-cap, verify strain relief, and test lamp strike. If issues persist, inspect lamp, transformer/ballast, and sleeve for faults.

Aqua Ultraviolet – Flow Switch (GRID) for Classic & SL Series — Complete with 2" Unions & Cords Overview Add automatic protection to your UV system. This in-line flow switch (GRID) interlocks power to the UV so the lamp only runs when water is moving—helping prevent overheated housings, scorched sleeves, and premature lamp failure. Key Features Auto safety interlock: cuts/enables UV power based on actual water flow Plug-and-play kit: includes 2" unions and pre-wired cords Reduces risk of sleeve discoloration and O-ring damage during dry-run events Works with Classic and SL series UV sterilizers Service-friendly unions for quick removal and cleaning Compatibility Aqua Ultraviolet Classic and SL UV sterilizers on 2" PVC plumbing Freshwater or saltwater systems (non-submersible installation) Specifications Type: In-line flow-sensing power interlock (GRID style) Plumbing: 2" slip unions (in/out) Use: Horizontal or vertical (follow flow arrow; avoid air traps) Electrical: Pre-wired cord set for simple UV power interlock (120V systems) Housing: Rigid PVC/engineered plastics for wet-location plumbing (external only) What’s Included (1) Flow Switch (GRID assembly) (2) 2" slip unions with O-rings Pre-wired power/control cords Quick start/installation guide Installation Notes Install after the pump and mechanical filtration; align with the flow arrow. Solvent-weld the 2" unions to your PVC; allow full cure before pressurizing. Mount the switch so the sensing chamber stays flooded (no trapped air). Connect the cords per the diagram to interlock UV power through the flow switch. Test by starting/stopping the pump—UV should turn off when flow stops. Never submerge the electrical components; keep cords and connections dry/secured.

Aqua Ultraviolet – Classic Inline UV Sterilizer, 80 Watt, 2" Socket (White) Overview High-capacity inline UV-C sterilizer for ponds and serious aquarium life-support. The Classic 80W with 2" socket (slip-union) ports uses two 40-watt lamps to deliver strong water clarity and pathogen reduction in a compact, service-friendly housing. Key Features Heavy-duty Classic body with 2" socket unions for high-flow PVC plumbing Dual-lamp (2 × 40W) design for robust UV dose and fast water polishing Targets free-floating algae, bacteria, and protozoa—no chemicals Clear end cap to confirm lamp-on status at a glance Weather-resistant (non-submersible) for indoor or protected outdoor installs Optional Wiper version available (not recommended for saltwater use) Sizing & Flow Guidance Sterilizer (freshwater): ~2,800–5,000 gal Sterilizer (saltwater): ~800–1,000 gal Clarifier (freshwater): up to ~10,000 gal (with 50–75% plant coverage) Typical UV-dose flow targets (EOL): ~3,200 GPH ≈ 30,000 µW·s/cm² (clarifying) ~2,150 GPH ≈ 45,000 µW·s/cm² ~1,600 GPH ≈ 60,000 µW·s/cm² ~1,280 GPH ≈ 75,000 µW·s/cm² ~1,070 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic Inline 80 Watt, 2" Socket, White (No Wiper) Lamps: (2) × 40W low-pressure UV-C Electrical: 120V / 60Hz (dual inline power supplies) Connections: 2" socket/slip unions (in/out) Dimensions (unit): ~20" × 3-3/4" × 16-1/2" Cord Length: ~15 ft Mounting: Supported inline or wall/stand (use proper brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 80W inline UV body (White, 2" socket ports) (2) 40W UV lamps Inline transformers/power supplies 2" slip unions Quick start/installation guide Installation Notes Install after mechanical filtration on a pressure line; follow the flow arrow. Solvent-weld 2" PVC into the sockets; allow full cure before pressurizing. Use valves/unions to tune flow to your target dose and simplify service. Protect power components from weather; do not submerge the unit. Replace both lamps every 9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – Classic Inline UV Sterilizer, 80 Watt, 2" Socket (Black) Overview High-capacity inline UV-C sterilizer for ponds and serious aquarium life-support. The Classic 80W with 2" socket (slip-union) ports uses two 40-watt lamps to deliver strong water clarity and pathogen reduction in a compact, service-friendly housing. Key Features Heavy-duty Classic body with 2" socket unions for high-flow PVC plumbing Dual-lamp (2 × 40W) design for robust UV dose and fast water polishing Targets free-floating algae, bacteria, and protozoa—no chemicals Clear end cap to confirm lamp-on status at a glance Weather-resistant (non-submersible) for indoor or protected outdoor installs Optional Wiper version available (not recommended for saltwater use) Sizing & Flow Guidance Sterilizer (freshwater): ~2,800–5,000 gal Sterilizer (saltwater): ~800–1,000 gal Clarifier (freshwater): up to ~10,000 gal (with 50–75% plant coverage) Typical UV-dose flow targets (EOL): ~3,200 GPH ≈ 30,000 µW·s/cm² (clarifying) ~2,150 GPH ≈ 45,000 µW·s/cm² ~1,600 GPH ≈ 60,000 µW·s/cm² ~1,280 GPH ≈ 75,000 µW·s/cm² ~1,070 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic Inline 80 Watt, 2" Socket, Black (No Wiper) Lamps: (2) × 40W low-pressure UV-C Electrical: 120V / 60Hz (dual inline power supplies) Connections: 2" socket/slip unions (in/out) Dimensions (unit): ~20" × 3-3/4" × 16-1/2" Cord Length: ~15 ft Mounting: Supported inline or wall/stand (use proper brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 80W inline UV body (Black, 2" socket ports) (2) 40W UV lamps Inline transformers/power supplies 2" slip unions Quick start/installation guide Installation Notes Install after mechanical filtration on a pressure line; follow the flow arrow. Solvent-weld 2" PVC into the sockets; allow full cure before pressurizing. Use valves/unions to tune flow to your target dose and simplify service. Protect power components from weather; do not submerge the unit. Replace both lamps every 9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – Classic Inline UV Sterilizer, 57 Watt, 3/4" Socket (Black) Overview High-output inline UV-C sterilizer for aquariums and small ponds. The Classic 57W with 3/4" socket unions plumbs into rigid 3/4" PVC for a clean, leak-resistant install—ideal for medium–large displays, reef/freshwater polishing loops, and QT systems. Key Features 3/4" socket (slip) unions for rigid-PVC plumbing Single 57W low-pressure UV-C lamp for algae/bacteria/protozoa control Clear end cap to confirm lamp-on status at a glance Weather-resistant (non-submersible) housing; compact, service-friendly layout Optional Wiper version available (not recommended for saltwater use) Sizing & Flow Guidance Sterilizer (freshwater): ~1,800–3,500 gal Sterilizer (saltwater): ~500–700 gal Clarifier (freshwater): up to ~8,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): ~3,600 GPH ≈ 30,000 µW·s/cm² (clarifying) ~2,400 GPH ≈ 45,000 µW·s/cm² ~1,800 GPH ≈ 60,000 µW·s/cm² ~1,440 GPH ≈ 75,000 µW·s/cm² ~1,200 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic Inline 57 Watt, 3/4" Socket, Black (No Wiper) Lamp: (1) × 57W low-pressure UV-C Electrical: 120V / 60Hz Connections: 3/4" slip (socket) unions, in/out Dimensions (unit): ~23" × 3-3/4" × 6" Cord Length: ~15 ft Mount: Supported inline or wall/stand (use suitable brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 57W inline UV body (Black, 3/4" socket ports) (1) 57W UV lamp Inline transformer/power supply 3/4" slip unions (model dependent) Quick start/installation guide Installation Notes Install after mechanical filtration on a pressure line; follow the flow arrow. Solvent-weld 3/4" PVC into the sockets; allow full cure before pressurizing. Use valves/unions to tune flow to your target dose and simplify service. Keep power components dry/ventilated; do not submerge the unit. Replace the lamp every 9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – Classic Inline UV Sterilizer, 57 Watt, 2" Socket (Black) Overview High-output inline UV-C sterilizer for ponds and aquariums. The Classic 57W with 2" socket (slip-union) ports delivers strong water clarity and pathogen reduction in a service-friendly housing—ideal for medium–large ponds, big displays, and reef life-support loops. Key Features Heavy-duty Classic body with 2" socket unions for high-flow plumbing Single 57W low-pressure UV-C lamp targets algae, bacteria, and protozoa Clear end cap shows lamp-on status at a glance Weather-resistant (non-submersible) for indoor or protected outdoor installs Optional Wiper version available (not recommended for saltwater use) Sizing & Flow Guidance Sterilizer (freshwater): ~1,800–3,500 gal Sterilizer (saltwater): ~500–700 gal Clarifier (freshwater): up to ~8,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): ~3,600 GPH ≈ 30,000 µW·s/cm² (clarifying) ~2,400 GPH ≈ 45,000 µW·s/cm² ~1,800 GPH ≈ 60,000 µW·s/cm² ~1,440 GPH ≈ 75,000 µW·s/cm² ~1,200 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic Inline 57 Watt, 2" Socket, Black (No Wiper) Lamp: (1) × 57W low-pressure UV-C Electrical: 120V / 60Hz Connections: 2" socket/slip unions (in/out) Dimensions (unit): ~23" × 3-3/4" × 6" Cord Length: ~15 ft Mounting: Supported inline or wall/stand (use appropriate brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 57W inline UV body (Black, 2" socket ports) (1) 57W UV lamp Inline transformer/power supply 2" union/slip set Quick start/installation guide Installation Notes Install after mechanical filtration on a pressure line; observe the flow arrow. Use unions/valves to tune flow to your target dose and simplify service. Protect power components from weather; do not submerge the unit. Replace the lamp every 9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – Classic Inline UV Sterilizer, 40 Watt, 3/4" Barb (Black) Overview Mid-size inline UV-C sterilizer for aquariums and small ponds. The Classic 40W with 3/4" barb fittings plumbs directly into flexible tubing to deliver strong water clarity and pathogen reduction—ideal for medium displays, QT systems, and reef/freshwater polishing loops. Key Features Inline 3/4" barb connections for quick hose-on installs Single 40W low-pressure UV-C lamp targets algae, bacteria, and protozoa Clear end cap lets you confirm lamp-on status at a glance Weather-resistant (non-submersible) housing with a compact, service-friendly layout Optional Wiper version available (not recommended for saltwater use) Sizing & Flow Guidance Sterilizer (freshwater): ~1,200–2,000 gal Sterilizer (saltwater): ~325 gal Clarifier (freshwater): up to ~6,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): ~2,900 GPH ≈ 30,000 µW·s/cm² (clarifying) ~1,930 GPH ≈ 45,000 µW·s/cm² ~1,450 GPH ≈ 60,000 µW·s/cm² ~1,160 GPH ≈ 75,000 µW·s/cm² ~967 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic Inline 40 Watt, 3/4" Barb, Black (No Wiper) Lamp: (1) × 40W low-pressure UV-C Electrical: 120V / 60Hz Plumbing: 3/4" hose barbs (use stainless clamps) Dimensions (unit): ≈38" × 4" × 2.5" Cord Length: ~15 ft Mount: Inline—horizontal or vertical (follow flow arrow) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 40W inline UV body (Black, 3/4" barbs) (1) 40W UV lamp Inline transformer/power supply Hose-barb kit / unions (model dependent) Quick start/installation guide Installation Notes Install after mechanical filtration and observe the flow arrow. Push tubing fully over barbs and secure with clamps; leak-test before use. Keep the power supply dry/ventilated; do not submerge any components. Replace the lamp every 9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – Classic Inline UV Sterilizer, 40 Watt, 2" Socket (Black) Overview Reliable mid-size inline UV-C sterilizer for ponds and aquariums. The Classic 40W with 2" socket (slip-union) ports delivers strong water clarity and pathogen reduction in a service-friendly housing—ideal for medium ponds, larger displays, and reef life-support loops. Key Features Heavy-duty Classic body with 2" socket unions for high-flow plumbing Single 40W low-pressure UV-C lamp targets algae, bacteria, and protozoa Clear end cap shows lamp-on status at a glance Weather-resistant (non-submersible) for indoor or protected outdoor installs Optional Wiper variant available (not recommended for saltwater use) Sizing & Flow Guidance Sterilizer (freshwater): ~1,200–2,000 gal Sterilizer (saltwater): ~325 gal Clarifier (freshwater): up to ~6,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): ~2,900 GPH ≈ 30,000 µW·s/cm² (clarifying) ~1,930 GPH ≈ 45,000 µW·s/cm² ~1,450 GPH ≈ 60,000 µW·s/cm² ~1,160 GPH ≈ 75,000 µW·s/cm² ~967 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic Inline 40 Watt, 2" Socket, Black (No Wiper) Lamp: (1) × 40W low-pressure UV-C Electrical: 120V / 60Hz Connections: 2" socket/slip unions (in/out) Dimensions (unit): ≈38" × 4" × 2.5" Cord Length: ~15 ft Mounting: Wall/stand or supported inline (use appropriate brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 40W UV body (Black, 2" socket ports) (1) 40W UV lamp Inline transformer/power supply 2" union/slip set Quick start/installation guide Installation Notes Install after mechanical filtration on a pressure line; avoid gravity-feed. Use unions/valves to tune flow to your target dose and simplify service. Protect from weather; do not submerge. Replace the lamp every 9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – Classic Inline UV Sterilizer, 25 Watt, 3/4" Barb (Black) Overview Compact, proven UV-C sterilizer for aquariums and small ponds. The Classic 25W with 3/4" barb fittings plumbs straight into flexible tubing to clear green water and reduce pathogen load—perfect for QT systems, nanos, and modest display tanks. Key Features Inline 3/4" barb connections for quick hose-on installs Single 25W low-pressure UV-C lamp targets algae, bacteria, and protozoa Clear end cap makes lamp-on status visible at a glance Weather-resistant (non-submersible) housing; quiet, compact footprint Optional Wiper variant available (not recommended for saltwater use) Sizing & Flow Guidance Sterilizer (freshwater): ~500–1,200 gal Sterilizer (saltwater): ~150 gal Clarifier (freshwater): up to ~4,000 gal Target UV-dose flows (EOL): ~1,200 GPH ≈ 30,000 µW·s/cm² (clarifying) ~800 GPH ≈ 45,000 µW·s/cm² ~600 GPH ≈ 60,000 µW·s/cm² ~480 GPH ≈ 75,000 µW·s/cm² ~400 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic Inline 25 Watt, 3/4" Barb, Black (No Wiper) Lamp: (1) × 25W low-pressure UV-C Electrical: 120V / 60Hz; ~0.48 A Plumbing: 3/4" hose barbs (use stainless clamps) Dimensions (unit): ~20" × 3-3/4" × 6" Cord Length: ~15 ft Mount: Inline—horizontal or vertical (follow flow arrow) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 25W inline UV body (Black, 3/4" barbs) (1) 25W UV lamp Inline transformer/power supply Hose-barb kit / unions (model dependent) Quick start/installation guide Installation Notes Install after mechanical filtration; observe the flow arrow. Push tubing fully over barbs and secure with clamps; leak-test before use. Keep the power supply dry/ventilated; do not submerge components. Replace the lamp every 9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – Classic Inline UV Sterilizer, 15 Watt, 3/4" Barb (Black) Overview Compact inline UV-C sterilizer for aquariums and small ponds. The Classic 15W with 3/4" barb fittings plumbs directly into flexible tubing to deliver clear water and reduced pathogen load—perfect for QT systems, nanos, and modest displays. Key Features Inline 3/4" barb connections for quick hose-on installs Single 15W low-pressure UV-C lamp targets algae, bacteria, and protozoa Clear end cap lets you verify lamp-on status at a glance Weather-resistant (non-submersible) body; quiet, compact footprint Optional Wiper variant available (not recommended for saltwater use) Sizing & Flow Guidance Sterilizer (freshwater): ~200–500 gal Sterilizer (saltwater): ~75 gal Clarifier (freshwater): up to ~2,000 gal Target UV-dose flows (EOL): ~700 GPH ≈ 30,000 µW·s/cm² (clarifying) ~466 GPH ≈ 45,000 µW·s/cm² ~350 GPH ≈ 60,000 µW·s/cm² ~233 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic Inline 15 Watt, 3/4" Barb, Black (No Wiper) Lamp: (1) × 15W low-pressure UV-C Electrical: 120V / 60Hz; ~0.48 A Plumbing: 3/4" hose barbs (use stainless clamps) Dimensions (unit): ~16" × 3-3/4" × 6" Cord Length: ~15 ft Mounting: Inline/horizontal or vertical (follow flow arrow) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 15W inline UV body (Black, 3/4" barbs) (1) 15W UV lamp Inline transformer/power supply Hose-barb kit / unions (model dependent) Quick start/installation guide Installation Notes Install after mechanical filtration on a pressure line; observe the flow arrow. Push tubing fully over barbs and secure with clamps; leak-test before use. Keep the power supply dry/ventilated; do not submerge any components. Replace the lamp every 9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – Classic Inline UV Sterilizer, 114 Watt, 2" Socket (Black) Overview High-capacity inline UV-C sterilizer for serious ponds and aquarium life-support. The Classic 114W uses two 57-watt lamps and 2" socket ports to deliver strong water clarity and pathogen reduction while keeping service simple and fast. Key Features Heavy-duty Classic housing with 2" socket (slip-union) connections for high-flow plumbing Dual-lamp (2 × 57W) design for robust UV dose and clear water Targets free-floating algae, bacteria, and protozoa without chemicals Weather-resistant, non-submersible body for indoor or protected outdoor installs Service-friendly layout; optional manual Wiper version available Sizing & Flow Guidance Sterilizer (freshwater): ~2,200–4,400 gal Sterilizer (saltwater): ~700 gal Clarifier (freshwater): up to ~9,500 gal (with 50–75% plant coverage) Typical UV-dose flow targets (EOL): ~3,900 GPH ≈ 30,000 µW·s/cm² (clarifying) ~2,600 GPH ≈ 45,000 µW·s/cm² ~1,950 GPH ≈ 60,000 µW·s/cm² ~1,560 GPH ≈ 75,000 µW·s/cm² ~1,300 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic Inline 114 Watt, 2" Socket, Black (No Wiper) Lamps: (2) × 57W low-pressure UV-C Electrical: 120V / 60Hz, approx. ~0.85 A total draw Connections: 2" socket/slip unions (in/out) Dimensions (unit): ~20" × 3-3/4" × 16-1/2" Cord Length: ~15 ft Mounting: Wall/stand (use appropriate brackets/anchors) Warranty: Limited lifetime on housing; 1 year on other components What’s Included Classic 114W UV body (Black, 2" socket ports) (2) 57W UV lamps Inline power supplies Union/fitting set (2" socket/slip) Quick start/installation guide Installation Notes Install after mechanical filtration on a pressure line; avoid gravity-feed. Use unions/valves to isolate the unit and dial in target flow. Protect from weather; do not submerge. Replace lamps every 9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – 25 Watt Classic UV Sterilizer, 3/4" (Black) with Wiper Overview Reliable, compact UV-C sterilizer for ponds and aquariums. This Classic 25W model with 3/4" ports adds a manual wiper to help keep the quartz sleeve clear between services—great for polishing loops, QT systems, and modest displays. Key Features Classic housing with 3/4" inlet/outlet for easy inline plumbing Single low-pressure 25W UV-C lamp for algae/bacteria/protozoa control Integrated manual wiper helps maintain sleeve clarity and consistent UV output Weather-resistant (non-submersible) body for indoor or protected outdoor installs Clear end cap shows lamp-on status; quick access for lamp/sleeve changes Note: Wipers are not recommended for saltwater use; using a wiper on saltwater can void the wiper warranty. Many marine installs choose the non-wiper variant and clean the sleeve during lamp changes. Sizing & Flow Guidance Sterilizer (freshwater): ~500–1,200 gal Sterilizer (saltwater): ~150 gal Clarifier (freshwater): up to ~4,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): ~1,200 GPH ≈ 30,000 µW·s/cm² ~800 GPH ≈ 45,000 µW·s/cm² ~600 GPH ≈ 60,000 µW·s/cm² ~480 GPH ≈ 75,000 µW·s/cm² ~400 GPH ≈ 90,000 µW·s/cm² (tighter pathogen control) Specifications Model: Classic 25 Watt, 3/4" Inlet/Outlet, Black, with Wiper Lamp: (1) × 25W low-pressure UV-C Electrical: 120 V / 60 Hz; ~0.48 A Connections: 3/4" (barb or slip style per kit) Dimensions (unit): 20" × 3-3/4" × 6" Dimensions with Wiper: 22-3/4" × 3-3/4" × 6" Wiper clearance: 12" Cord Length: ~15 ft Mounting: Wall/stand (use suitable brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components (wiper excluded from saltwater coverage) What’s Included Classic 25W UV body (Black, 3/4" ports) with manual wiper (1) 25W UV lamp Inline power supply Union/fitting set (3/4") Quick start/installation guide Installation Notes Plumb after mechanical filtration on a pressure line; avoid gravity-feed. Add unions/valves for service and to set flow. Operate the wiper with the lamp off; relieve pressure before wiping. Protect from weather; do not submerge. Replace the lamp every ~9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – Classic 120 Watt UV Sterilizer, 2" (White) Overview High-output UV-C sterilizer for large ponds and serious aquarium life-support. The Classic 120W with 2" slip ports uses a three-lamp array to deliver strong water clarity and pathogen reduction in a service-friendly housing. Key Features Heavy-duty Classic body with 2" slip inlet/outlet for high-flow plumbing Tri-lamp design (3 × 40W) for robust UV dose and fast water polishing Clears green water; reduces algae, bacteria, and protozoa load Weather-resistant (non-submersible) for indoor or protected outdoor installs Service-friendly: quick-release tee, EZ-twist cap, clear quartz cap (lamp-on view) Sizing & Flow Guidance Sterilizer (freshwater): ~4,400–6,000 gal Sterilizer (saltwater): ~900 gal Clarifier (freshwater): up to ~12,000 gal (with 50–75% plant coverage) Target UV-dose flows (EOL): up to ~4,080 GPH at ~30,000 µW·s/cm² (reduce flow for higher doses/pathogen control) Specifications Model: Classic 120 Watt, 2" Inlet/Outlet, White (No Wiper) Lamps: (3) × 40W low-pressure UV-C Electrical: 120V / 60Hz, approx. 1.33 A total draw Connections: 2" slip (in/out) Dimensions (2" unit): 36-7/8" × 3-3/4" × 21-3/8" Cord Length: ~15 ft Mounting: Wall/stand (use appropriate brackets/anchors) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Classic 120W UV body (White, 2" ports) (3) 40W UV lamps Remote transformer/power supply Union/fitting set (2" slip) Quick start/installation guide Installation Notes Install after mechanical filtration on a pressure line; avoid gravity-feed. Use unions/valves to isolate the unit and dial in target flow. Protect from weather; do not submerge. Replace lamps every 9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – Advantage 2000+ Inline UV Sterilizer, 15 Watt Overview Compact inline UV-C sterilizer for aquariums and small ponds. The Advantage 2000+ 15W plumbs directly into your return, canister loop, or a small utility pump to deliver clear water and reduced pathogen load—perfect for quarantine tanks, nanos, and medium displays where space is tight. Key Features Inline plumbing—easy add-on to returns/canisters or a small pump 15W low-pressure UV-C lamp targets algae, bacteria, and protozoa Service-friendly body with clear end cap to confirm lamp-on status Quiet, compact footprint; horizontal or vertical install (follow flow arrow) Works for freshwater and marine systems (non-submersible unit) Sizing & Flow Guidance Ideal for nano to mid-size aquariums and QT systems Target ~150–300 GPH for sterilization; higher flow is fine for clarification For tighter pathogen control, run toward the lower end of the range Specifications Model: Advantage 2000+ Inline, 15 Watt Plumbing: Inline hose barbs (commonly 5/8"–3/4", kit dependent) Lamp: (1) × 15W low-pressure UV-C Electrical: 120V / 60Hz inline power supply Finish: Black, weather-resistant (non-submersible) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Advantage 2000+ Inline 15W UV body (1) 15W UV lamp Inline transformer/power supply Hose barbs/mount hardware Quick start/installation guide Installation Notes Install after mechanical filtration on a pressure line; observe the flow arrow. Use unions/valves to set flow and simplify service. Keep the power supply dry and ventilated; do not submerge components. Replace the lamp every 9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – Advantage 2000 Inline UV Sterilizer, 8 Watt Overview Compact inline UV-C sterilizer for aquariums and small ponds. The Advantage 2000 8W plumbs directly into your return/canister loop for clear water and reduced pathogen load—perfect for quarantine tanks, nanos, and medium displays where space is tight. Key Features Inline plumbing—easy add-on to returns, canisters, or small utility pumps 8W low-pressure UV-C lamp targets algae, bacteria, and protozoa Service-friendly body with clear end cap to confirm lamp-on status Quiet, compact footprint; mount horizontally or vertically (per flow arrow) Works for freshwater and marine systems (non-submersible unit) Sizing & Flow Guidance Ideal for nano to mid-size aquariums and QT systems Target ~100–200 GPH for sterilization; higher flow acceptable for clarifying only For tighter pathogen control, run toward the lower end of the range Specifications Model: Advantage 2000 Inline, 8 Watt Plumbing: Inline hose barbs (commonly 5/8"–3/4" depending on kit) Lamp: (1) × 8W low-pressure UV-C Electrical: 120V / 60Hz inline power supply Finish: Black, weather-resistant (non-submersible) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Advantage 2000 Inline 8W UV body (1) 8W UV lamp Inline transformer/power supply Hose barbs/mount hardware Quick start/installation guide Installation Notes Install after mechanical filtration on a pressure line. Observe the flow arrow; use unions/valves to set flow and ease service. Keep the power supply dry and ventilated; do not submerge any components. Replace the lamp every 9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – Advantage 2000 Hang-On UV Sterilizer, 8 Watt Overview A compact, hang-on-back UV sterilizer designed for easy add-on clarity and pathogen control. The Advantage 2000 8W mounts directly on the rim of most aquariums—perfect for quarantine tanks, nano/medium reef or freshwater displays, and polishing loops where space is tight. Key Features Hang-on design — no stand or wall mount needed Plug-and-play 8W low-pressure UV-C lamp for algae/bacteria/protozoa control Quick-service layout with clear end cap to verify lamp-on status Quiet, compact body suitable for display tanks or sumps Works with canister/return lines or a small utility pump (pump not included) Sizing & Flow Guidance Great for nano to mid-size aquariums and QT systems Target ~100–200 GPH for sterilization; higher flow acceptable for simple water clarification For marine/pathogen control, favor the lower end of the flow range for higher UV dose Specifications Model: Advantage 2000 HOB, 8 Watt Mount: Hang-on-back (standard aquarium rims) Lamp: (1) × 8W low-pressure UV-C Electrical: 120V / 60Hz inline power supply Plumbing: 5/8" hose barbs (typical) — integrates with small pumps or return lines Finish: Black, weather-resistant (non-submersible) Warranty: Limited lifetime on housing; 1-year on other components What’s Included Advantage 2000 8W HOB UV body (1) 8W UV lamp Inline transformer/power supply Hose barbs/mount hardware Quick start/installation guide Installation Notes Hang unit on tank rim or sump wall; ensure vertical orientation. Plumb after mechanical filtration; use valves/unions for service and to set flow. Protect power supply from splashes; do not submerge any components. Replace the lamp every 9–12 months of continuous use to maintain dose.

Aqua Ultraviolet – 80 Watt Replacement Raw Transformer / Ballast Overview OEM raw transformer/ballast for Aqua Ultraviolet 80W UV sterilizers. Replaces a failed or aging power component to restore reliable lamp ignition and correct operating current. Key Features Genuine replacement power component for 80-watt Aqua UV lamps Provides proper start and run current for stable UV output “Raw” (unhoused) part—ideal for service benches and in-house repairs Compatible with wiper and non-wiper models Compatibility Aqua Ultraviolet Classic 80W UV sterilizers (all port sizes) Not for other wattages (8W/15W/25W/40W/57W/114W/160W/etc.) Specifications Type: Low-pressure UV-C lamp transformer/ballast (80W) Input: 120V AC, 60Hz (typical) Output: Matched to Aqua UV 80W low-pressure UV-C lamp Form Factor: Raw component (no outer housing) Leads: Pigtail wiring for line/neutral/ground and lamp connections What’s Included (1) 80W raw transformer/ballast Installation & Safety Notes Disconnect power and isolate plumbing before service. Mount in a dry, ventilated area—do not submerge or expose to spray. Follow the factory wiring diagram; correctly terminate line/neutral/ground. Use proper connectors/heat-shrink and strain-relief. After installation, verify lamp strike and amperage; replace aged lamps/sleeve as needed.

Aqua Ultraviolet – 8 Watt Transformer (Black), 120V/60Hz Overview OEM replacement transformer/power supply for Aqua Ultraviolet 8W UV sterilizers. Restores proper lamp ignition and stable operating current; plug-and-play with the standard black transformer housing. Key Features Genuine Aqua Ultraviolet replacement transformer for 8-watt lamps Pre-wired, black housing for quick swap and tidy installs Delivers correct start and run current to maintain UV output Works with wiper and non-wiper 8W models Compatibility Aqua Ultraviolet Classic 8W UV sterilizers (all port sizes) Not compatible with other wattages (15W/25W/40W/57W/etc.) Specifications Input: 120V AC, 60Hz Output: Matched to Aqua UV 8W low-pressure UV-C lamp Housing: Black, dry-location use (non-submersible) Leads/Connector: Factory-terminated (model dependent) What’s Included (1) 8W transformer/power supply, black housing Installation & Safety Notes Disconnect power and isolate the unit before service. Mount in a dry, ventilated location; do not submerge or expose to spray. Follow the factory wiring/plug instructions; ensure proper line/neutral/ground. After install, verify lamp strike and operation; replace aged lamps/sleeves as needed.