33043a-03

Aqua Ultraviolet – Ultima II 1,000 Filter with 1.5" Multi-Port Valve Overview Compact, pressurized bead filter for ponds and water features up to 1,000 gallons. The Ultima II 1,000 combines non-clogging bio-media with a powerful backwash to deliver clear, polished water with minimal maintenance—perfect for smaller koi ponds, quarantine systems, and fountains. Key Features Pressurized bead+bio filtration using high-surface-area Bio-Tubes Cyclonic backwash lifts and purges debris fast—no messy media cleaning 1.5" multi-port valve with intuitive positions (Filter, Backwash, Rinse, Waste, Recirculate, Closed) Low headloss design pairs well with external or submersible pumps UV- and weather-resistant vessel for equipment pads or sheds (non-submersible) Sizing & Flow Guidance Pond capacity: up to 1,000 gal (heavy fish load or full sun may require upsizing) Target pump flow: ~1,000–2,000 GPH through the 1.5" valve for best performance Backwash when pressure rises ~5–8 psi above clean baseline Specifications Model: Ultima II 1,000 Valve: 1.5" side-mount multi-port Operation: Pressurized, backwashable bead/bio-media Ports: 1.5" slip at valve (adapt as needed) Orientation: Outdoor-ready; install level and well-supported Warranty: Manufacturer limited warranty on tank/valve (see terms) What’s Included Ultima II 1,000 filter vessel pre-loaded with media 1.5" multi-port valve (handle & sight glass) Union/tailpiece set (model dependent) Quick start/installation guide Installation Notes Set on a level, load-bearing pad near the pump and returns. Plumb pump to valve IN, valve OUT to pond/returns; add a WASTE line for backwash. Use unions and 1.5" PVC to minimize headloss; keep runs short/smooth. On first start, run Rinse briefly, then switch to Filter. Backwash when the gauge rises 5–8 psi or on a regular schedule for high-load systems.

Aqua Ultraviolet – Ultima II 10,000 Filter w/ 2" Multi-Port Valve Overview High-capacity, pressurized bead filter for ponds and water features up to 10,000 gallons. The Ultima II 10,000 combines dense, non-clogging bio-media with a powerful backwash system to deliver crystal-clear water with minimal maintenance. Key Features Pressurized “bead” filtration with high-surface-area Bio-Tubes for mechanical + biological polishing Cyclonic backwash agitates and lifts debris for fast, low-waste cleaning 2" multi-port valve (side-mount) with simple handle positions (Filter, Backwash, Rinse, Waste, Recirculate, Closed) Low headloss design—pairs well with external pumps on long runs UV- and weather-resistant, corrosion-proof vessel for outdoor equipment pads Sizing & Flow Guidance Pond capacity: up to 10,000 gal (stocking/feeding and sun exposure may reduce real-world capacity—oversize when in doubt) Typical pump pairing: ~7,500–10,000 GPH target flow through the 2" valve For koi/high load, consider upsizing pump/filter or running a prefilter for best results Specifications Model: Ultima II 10,000 Valve: 2" side-mount multi-port Operation: Pressurized, backwashable bead/bio-media system Ports: 2" slip (common) at valve ports (adapt as needed) Orientation: Outdoor-ready (non-submersible); level pad or equipment stand Warranty: Manufacturer limited warranty on tank/valve (see terms) What’s Included Ultima II 10,000 filter vessel pre-loaded with media 2" multi-port valve (handle, sight glass) Union set / tailpieces (model dependent) Backwash drain/waste port Quick start/installation guide Installation Notes Place on a level, load-bearing pad near pump and returns. Plumb pump to valve IN, valve OUT to pond/returns; add waste line for backwash. Use unions and 2" PVC where possible to minimize headloss. Start in Rinse after media loads with water, then set to Filter. Backwash when the pressure gauge rises ~5–8 psi above clean baseline (or weekly in heavy-load ponds).

Aqua Ultraviolet – Ultima II 2,000 Filter with 1.5" Multi-Port Valve Overview Pressurized bead/bio filter for ponds and water features up to 2,000 gallons. The Ultima II 2,000 pairs non-clogging media with a powerful cyclonic backwash to keep water sparkling with minimal maintenance—ideal for small koi ponds, quarantine systems, and compact water gardens. Key Features Bead + biological filtration using high–surface area Bio-Tubes Cyclonic backwash lifts and purges debris—no messy media handling 1.5" multi-port valve with simple positions (Filter, Backwash, Rinse, Waste, Recirculate, Closed) Low head-loss design for efficient pump pairing Weather/UV-resistant, corrosion-proof vessel (non-submersible) Sizing & Flow Guidance Pond capacity: up to 2,000 gal (heavier stocking/full sun may require upsizing) Target pump flow through valve: ~1,500–2,500 GPH (match to fish load and plumbing) Backwash when pressure rises ~5–8 psi above clean baseline Specifications Model: Ultima II 2,000 Valve: 1.5" side-mount multi-port Ports: 1.5" slip at valve (adapt as needed) Operation: Pressurized, backwashable bead/bio-media system Installation: Outdoor equipment pad or shed; level, well-supported base Warranty: Manufacturer limited warranty on tank/valve (see terms) What’s Included Ultima II 2,000 filter vessel pre-loaded with media 1.5" multi-port valve (handle & sight glass) Union/tailpiece set (model dependent) Quick start/installation guide Installation Notes Place on a level, load-bearing pad near pump/returns. Plumb pump to valve IN, valve OUT to pond/returns; add a WASTE line for backwash. Use unions and 1.5" PVC to minimize headloss; keep runs smooth and short. On startup, run Rinse briefly, then switch to Filter. Backwash when the gauge indicates +5–8 psi or on a regular schedule for high-load ponds.

Aqua Ultraviolet – Ultima II 4,000 Filter with 1.5" Multi-Port Valve Overview Dependable, pressurized bead/bio filter for ponds and water features up to 4,000 gallons. The Ultima II 4,000 uses non-clogging media and a powerful cyclonic backwash to keep water clear with minimal routine maintenance—great for koi ponds and heavily stocked water gardens. Key Features Bead + biological filtration with high–surface area Bio-Tubes Cyclonic backwash lifts and purges debris fast—no messy media handling 1.5" multi-port valve with simple positions (Filter, Backwash, Rinse, Waste, Recirculate, Closed) Low head-loss design for efficient pump pairing and long plumbing runs UV- and weather-resistant vessel for outdoor equipment pads (non-submersible) Sizing & Flow Guidance Pond capacity: up to 4,000 gal (heavier stocking/full sun may require upsizing) Target pump flow: ~3,000–4,500 GPH through the 1.5" valve Backwash when pressure rises ~5–8 psi above clean baseline Specifications Model: Ultima II 4,000 Valve: 1.5" side-mount multi-port Ports: 1.5" slip at valve (adapt as needed) Operation: Pressurized, backwashable bead/bio-media system Install: Level, well-supported base; outdoor-ready housing Warranty: Manufacturer limited warranty on tank/valve (see terms) What’s Included Ultima II 4,000 filter vessel pre-loaded with media 1.5" multi-port valve (handle & sight glass) Union/tailpiece set (model dependent) Quick start/installation guide Installation Notes Set on a level, load-bearing pad near the pump and returns. Plumb pump to valve IN, valve OUT to pond/returns; add a WASTE line for backwash. Use unions and 1.5" PVC to minimize head loss; keep runs smooth/short. On startup, run Rinse briefly, then switch to Filter. Backwash at +5–8 psi over clean baseline or on a regular schedule in high-load systems.

Aqua Ultraviolet – Ultima II 6,000 Filter with 2" Multi-Port Valve Overview Robust, pressurized bead/bio filter for ponds and water features up to 6,000 gallons. The Ultima II 6,000 combines non-clogging media with a powerful cyclonic backwash to keep water crystal clear with minimal routine maintenance—ideal for koi ponds and heavily stocked water gardens. Key Features Bead + biological filtration using high–surface-area Bio-Tubes media Cyclonic backwash lifts and purges debris fast—no messy media cleaning 2" multi-port valve with simple handle positions (Filter, Backwash, Rinse, Waste, Recirculate, Closed) Low head-loss design supports long plumbing runs and external pumps UV- and weather-resistant, corrosion-proof vessel for outdoor pads (non-submersible) Sizing & Flow Guidance Pond capacity: up to 6,000 gal (heavy fish load/full sun may require upsizing) Target pump flow: ~4,000–6,000 GPH through the 2" valve for best performance Backwash when the pressure gauge rises ~5–8 psi above clean baseline Specifications Model: Ultima II 6,000 Valve: 2" side-mount multi-port Ports: 2" slip at valve (adapt as needed) Operation: Pressurized, backwashable bead/bio-media system Installation: Outdoor-ready; level, well-supported base Warranty: Manufacturer limited warranty on tank/valve (see terms) What’s Included Ultima II 6,000 filter vessel pre-loaded with media 2" multi-port valve (handle & sight glass) Union/tailpiece set (model dependent) Quick start/installation guide Installation Notes Place on a level, load-bearing pad near pump and returns. Plumb pump to valve IN, valve OUT to pond/returns; add a WASTE line for backwash. Use unions and 2" PVC to minimize head loss; keep runs smooth and short. On first start, run Rinse briefly, then switch to Filter. Backwash at +5–8 psi or on a regular schedule for high-load systems.

Aqua Ultraviolet – ULTIMA II Filter O-Ring (for 1,000–20,000 Models) Overview OEM replacement tank/valve O-ring for Aqua Ultraviolet Ultima II pressurized filters. Restores a drip-tight seal between the multi-port valve and filter body to stop leaks and air draw. Key Features Genuine Aqua Ultraviolet seal for Ultima II filters Sized to fit the full family: 1,000 / 2,000 / 4,000 / 6,000 / 10,000 / 20,000 Resilient elastomer; compatible with silicone-safe lubricants Quick, tool-light fix for weeping or flattened gaskets Compatibility Aqua Ultraviolet Ultima II filters from 1,000 up to 20,000 gallons Seats between the multi-port valve and filter vessel lid (verify placement in your manual) Specifications Part Type: Valve-to-tank O-ring Material: Durable elastomer (black) Environment: External, wet-location seal (non-submersible component by itself) What’s Included (1) ULTIMA II O-ring (fits 1,000–20,000 series) Installation Notes Shut off pump and relieve pressure; set valve to Closed. Remove the multi-port valve; lift out the old O-ring and clean groove/mating faces. Lightly coat the new O-ring with silicone-safe lubricant—no petroleum products. Seat evenly in the groove; reinstall valve hand-tight, then snug—do not overtighten. Pressurize and leak-test; recheck after the first backwash cycle.

Aqua Ultraviolet – ULTIMA II Valve Cover O-Ring (for 1.5" Valve) Overview OEM replacement valve cover O-ring for Aqua Ultraviolet Ultima II filters equipped with the 1.5" multi-port valve. Restores a drip-tight seal on the valve lid to stop leaks and prevent air draw. Key Features Genuine Aqua Ultraviolet 1.5" valve cover seal Resilient elastomer for long service life Seats easily; compatible with silicone-safe lubricants Quick, tool-light fix for weeping lids or flattened gaskets Compatibility Fits Ultima II filters using the 1.5" multi-port valve (e.g., 1,000 / 2,000 / 4,000 models and any kit with a 1.5" valve) For 2" valves (6,000/10,000/20,000), use the corresponding 2" valve cover O-ring Specifications Part Type: Valve cover O-ring (lid seal) Size: For 1.5" multi-port valve assembly Material: Durable elastomer (black) Use: External sealing surface (non-submersible component by itself) What’s Included (1) Valve cover O-ring for 1.5" Ultima II valve Installation Notes Shut off pump and relieve system pressure; set valve to Closed. Remove the valve cover; pull the old O-ring and clean the groove and mating face. Lightly coat the new O-ring with silicone-safe lubricant—avoid petroleum products. Seat evenly, reinstall the cover hand-tight, then snug—do not overtighten. Pressurize and leak-test; recheck after the first backwash cycle.

Aqua Ultraviolet – Ultima Ultra Media (8.5 lbs) Overview Genuine Ultima Ultra Media refill pack for Aqua Ultraviolet Ultima/Ultima II bead-bio filters. The non-clogging, high–surface area media supports both mechanical trapping and biological filtration to keep water crystal clear. Key Features OEM Ultra Media for optimal performance in Ultima/Ultima II filters Unique tubular shapes resist clumping and channeling during backwash High protected surface area promotes strong nitrifying bacteria colonies Durable, inert plastic—won’t compact or break down under normal use Compatibility For Aqua Ultraviolet Ultima & Ultima II pressurized filters Use to replace lost media or top off after thorough cleanings/repairs Check your filter’s manual for the recommended total media volume per model Specifications Product: Ultima Ultra Media Net Weight: 8.5 lbs (loose media) Material: Inert, UV- and chemical-resistant plastic bio-media Function: Mechanical polishing + biological filtration in pressurized bead filters What’s Included (1) Bag Ultima Ultra Media — 8.5 lbs Use & Maintenance Before adding, rinse media to remove shipping dust. Add through the filter’s top opening per manual; do not overfill beyond the stated media level. Resume operation and backwash per your gauge (typically +5–8 psi over clean baseline) or on a regular schedule for high-load ponds.

Aqua Ultraviolet – Union Half 3/4" Reducer Bushing (No Thread) with O-Ring — White Overview OEM reducer union half that adapts an Aqua Ultraviolet union to 3/4" without threads. Ideal when converting from larger union bodies to 3/4" smooth (slip/socket) plumbing. Includes a fresh O-ring for a drip-tight seal. Key Features Genuine Aqua Ultraviolet union half + reducer bushing No-thread (smooth) interface for solvent-weld PVC connections Includes O-ring sized for the factory groove Durable, chemical- and UV-resistant white polymer Compatibility Fits Aqua Ultraviolet Classic / Advantage / SL unions that accept interchangeable tails/reducer bushings Use when stepping down union connection to 3/4" slip; verify your union body style before ordering Specifications Size: Union half with 3/4" reducer bushing (smooth, no threads) Seal: Matching O-ring (included) Color/Material: White engineered polymer Use: External plumbing; non-submersible component What’s Included (1) Union half with integrated 3/4" reducer bushing — white (1) Union O-ring Installation Notes Shut off pump and relieve pressure. Clean union faces and groove; lightly lube O-ring with silicone-safe grease. Seat O-ring, solvent-weld 3/4" PVC into the smooth bushing (allow full cure). Assemble union hand-tight, then snug—do not overtighten. Pressurize and leak-test.

Aqua Ultraviolet – Union Half 3/4" with O-Ring Overview OEM replacement 3/4" union half for Aqua Ultraviolet UV sterilizers and accessories. Includes a fresh O-ring to restore a clean, drip-tight connection when a union half is cracked, cross-threaded, or missing. Key Features Genuine Aqua Ultraviolet 3/4" union half Includes O-ring sized for the factory groove Durable, chemical-resistant construction Enables quick, tool-light disassembly for maintenance or winterizing Compatibility Fits Aqua Ultraviolet Classic / Advantage / SL models that use 3/4" unions Matches the opposite factory union half on the unit (verify your union style—slip, barb, or socket—before ordering) Specifications Size: 3/4" union half (single side) Seal: 3/4" union O-ring (included) Material: UV- and corrosion-resistant polymer Use: External plumbing; non-submersible component What’s Included (1) 3/4" union half (1) 3/4" union O-ring Installation Notes Shut off pump and relieve pressure. Separate the union; remove the old O-ring and clean groove/sealing faces. Lightly lube the new O-ring with silicone-safe grease; seat evenly. Hand-tighten, then snug—do not overtighten. Pressurize and leak-test.

Aqua Ultraviolet – Union Ring (Nut), 2" — White Overview OEM replacement 2" union ring (nut) for Aqua Ultraviolet UV sterilizers and filters. Replaces cracked or stripped rings to restore a secure, serviceable, leak-free connection. Key Features Genuine Aqua Ultraviolet 2" union ring Durable, chemical- and UV-resistant white polymer Knurled/ergonomic profile for easy hand-tightening Works with factory union halves and O-rings for drip-tight seals Compatibility Fits Aqua Ultraviolet Classic / SL / Ultima components that use 2" slip/socket unions Pairs with the standard 2" union body/half and 2" union O-ring (O-ring not included) Specifications Part: Union ring (nut) — 2", white Material: Corrosion-resistant engineered polymer Use: External plumbing; non-submersible component What’s Included (1) 2" white union ring (nut only; O-ring and tailpieces sold separately) Installation Notes Inspect union faces and replace the O-ring if flattened or cracked. Lightly lube the O-ring with silicone-safe grease and seat it in the groove. Align union halves and thread the ring on hand-tight, then snug—do not overtighten. Pressurize and leak-test.

Aqua Ultraviolet – Union Ring, 2" (Black) Overview OEM replacement 2" union ring (nut) for Aqua Ultraviolet UV sterilizers and filters. Restores a secure, serviceable connection when the original ring is cracked, stripped, or missing. Key Features Genuine Aqua Ultraviolet 2" union ring Durable, chemical- and UV-resistant black polymer Knurled/ergonomic profile for easy hand-tightening Works with factory union halves and O-rings for drip-tight seals Compatibility Fits Aqua Ultraviolet Classic / SL / Ultima components that use 2" slip/socket unions Matches factory 2" union body/half and standard 2" union O-ring (O-ring not included) Specifications Part: Union ring (nut) — 2", black Material: Corrosion-resistant engineered polymer Use: External plumbing; non-submersible part What’s Included (1) 2" black union ring (nut only; O-ring and tailpieces sold separately) Installation Notes Inspect mating union faces and replace the O-ring if flattened or cracked. Lightly lube O-ring with silicone-safe grease, seat in groove. Align union halves and thread the union ring on hand-tight, then snug—do not overtighten. Pressurize and leak-test.

Aqua Ultraviolet – UV Mounting Bracket (Single) Overview Secure your Aqua Ultraviolet UV sterilizer to a wall or stand with this factory mounting bracket. The integrated grip-hold clip keeps the sterilizer body from shifting or twisting, making installs tidy and serviceable. Key Features Purpose-built for Aqua Ultraviolet UV sterilizers Grip-hold clip helps prevent movement and vibration Sold individually (most single-lamp units use 2 brackets) Simple, tool-light installation for clean, professional mounting Compatibility Fits most Aqua Ultraviolet units with a 2" body (e.g., common single-lamp Classic bodies). For multi-lamp or larger/heavier models, use additional brackets as needed. Specifications Item: UV Mounting Bracket (Single) MPN: A40124 UPC: 617750401249 Finish/Material: Durable molded bracket with integrated grip clip Use: Indoor/aquarium, pond, and life-support equipment rooms What’s Included (1) Aqua Ultraviolet UV Mounting Bracket Installation Notes Position the bracket on a flat, load-bearing surface. Mark and fasten using appropriate anchors/screws for your substrate (not included). Snap the UV body into the grip-hold clip. If supporting a vertical install or long runs of plumbing, use a second bracket for proper support.

Aqua Ultraviolet – VIPER 400W Lamp Kit for 3" Plastic Unit Overview Factory lamp kit for the Aqua Ultraviolet VIPER 400W (3" plastic) sterilizer. Restores peak germicidal performance in high-flow, large-system applications using a single high-output, low-pressure (amalgam) UV-C lamp. Key Features Genuine Aqua UV 400-watt HO UV-C lamp for VIPER 3" plastic housings Matched components to maintain proper fit, sealing, and UV dose Fast, service-friendly swap to keep downtime to a minimum Supports clear water and pathogen reduction in demanding, high-GPH systems Compatibility For VIPER 400W UV sterilizers with the 3" plastic body Not for stainless units or other wattages (800W/1200W) Specifications Lamp Power: 400 W (low-pressure UV-C, amalgam) Peak Wavelength: ~254 nm germicidal Housing Fit: 3" plastic VIPER assembly Service Life: Replace ~9–12 months of continuous use (or per meter/dose targets) What’s Included (1) 400W UV-C lamp (VIPER, 3" plastic fit) (1) Set of end seals/O-rings matched to the lamp end assembly (1) Quartz end cap/insulator or hardware as required for this kit (model dependent) Quick install sheet Contents may vary slightly by production run; all parts are OEM and matched for the 3" plastic VIPER 400W. Installation & Safety Notes Power OFF and lock out the circuit; allow the unit to cool. Isolate and depressurize plumbing; drain the UV chamber. Open end assembly, remove old lamp and seals; do not touch new lamp glass with bare hands. Inspect/clean the quartz sleeve; replace if etched or cracked. Install new seals lightly lubricated with silicone-safe grease; seat squarely. Reassemble hand-tight, then snug—do not overtighten. Restore flow, then power ON and verify operation; check for leaks after first run.

Aqua Ultraviolet – VIPER 400W Lamp Kit, 2" Plastic Unit Overview Factory lamp kit for the Aqua Ultraviolet VIPER 400W UV sterilizer with the 2" plastic housing. Restores peak germicidal performance for large, high-flow systems using a single high-output, low-pressure (amalgam) UV-C lamp. Key Features Genuine Aqua UV 400-watt HO UV-C lamp matched to 2" plastic VIPER units OEM seals/hardware ensure correct fit, sealing, and stable UV dose Service-friendly kit minimizes downtime on critical life-support loops Ideal for aquaculture, big ponds, and commercial aquarium systems Compatibility For VIPER 400W sterilizers in the 2" plastic configuration Not compatible with 2"/3" stainless or 3" plastic VIPER bodies, nor other wattages (800W/1200W) Specifications Lamp Power: 400 W (low-pressure amalgam UV-C) Peak Wavelength: ~254 nm (germicidal) Housing Fit: 2" plastic VIPER chamber Service Life: Replace about every 9–12 months of continuous use (or per UV meter/dose targets) What’s Included (1) 400W UV-C lamp — VIPER, 2" plastic fit (1) Set of end seals/O-rings sized for the 2" plastic end assembly (1) Set of required end hardware/insulator(s) (kit dependent) Quick install sheet Installation & Safety Notes Disconnect power and allow the unit to cool; isolate and depressurize plumbing. Open end assembly; remove the old lamp and seals (avoid touching new lamp glass). Inspect/clean the quartz sleeve; replace if cloudy, etched, or cracked. Lightly lube new O-rings with silicone-safe grease; seat squarely. Reassemble hand-tight, then snug—do not overtighten. Restore flow, power ON, verify strike, and check for leaks after first run. Want me to format this as a single-row Shopify CSV with your standard columns and tags?

Aqua Ultraviolet – VIPER 400W Lamp Kit, 2" Stainless Steel Overview Factory lamp kit for the Aqua Ultraviolet VIPER 400W UV sterilizer with 2" stainless steel housing. Restores peak germicidal performance for large, high-flow systems using a single high-output, low-pressure (amalgam) UV-C lamp. Key Features Genuine Aqua UV 400-watt HO UV-C lamp matched to 2" stainless VIPER units Maintains correct fit, sealing, and UV dose for reliable operation Service-friendly kit minimizes downtime on critical life-support systems Ideal for aquaculture, large ponds, commercial displays, and LSS loops Compatibility For VIPER 400W sterilizers in 2" stainless steel configuration Not compatible with 3" plastic VIPER bodies or other wattages (800W/1200W) Specifications Lamp Power: 400 W (low-pressure amalgam UV-C) Peak Wavelength: ~254 nm (germicidal) Housing Fit: 2" stainless VIPER chamber Service Life: Replace about every 9–12 months of continuous use (or per UV meter/dose targets) What’s Included (1) 400W UV-C lamp — VIPER, 2" stainless fit (1) Set of end seals/O-rings sized for stainless VIPER end assembly (1) Set of required end hardware/insulator(s) (kit dependent) Quick install sheet Installation & Safety Notes Disconnect power and allow the unit to cool fully. Isolate and depressurize plumbing; drain the chamber. Open end assembly; remove old lamp and seals (avoid touching new lamp glass). Inspect/clean the quartz sleeve; replace if etched, cloudy, or cracked. Lightly lube new O-rings with silicone-safe grease; seat squarely. Reassemble hand-tight, then snug—do not overtighten. Restore flow, power ON, verify strike, and check for leaks after first run.

Overview Factory lamp kit for the Aqua Ultraviolet VIPER 400W UV sterilizer with 3" stainless steel housing. Restores peak germicidal performance in large, high-flow systems using a single high-output, low-pressure (amalgam) UV-C lamp. Key Features Genuine Aqua UV 400-watt HO UV-C lamp matched to 3" stainless VIPER units OEM-matched components to maintain correct fit, sealing, and UV dose Service-friendly kit minimizes downtime on critical life-support loops Ideal for aquaculture, big ponds, and commercial aquarium systems Compatibility For VIPER 400W sterilizers in 3" stainless steel configuration Not compatible with 2" stainless or 3" plastic VIPER bodies, nor other wattages (800W/1200W) Specifications Lamp Power: 400 W (low-pressure amalgam UV-C) Peak Wavelength: ~254 nm (germicidal) Housing Fit: 3" stainless VIPER chamber Service Life: Replace about every 9–12 months of continuous use (or per UV meter/dose targets) What’s Included (1) 400W UV-C lamp — VIPER, 3" stainless fit (1) Set of end seals/O-rings sized for the 3" stainless end assembly (1) Set of required end hardware/insulator(s) (kit dependent) Quick install sheet Installation & Safety Notes Disconnect power and let the unit cool. Isolate and depressurize plumbing; drain the chamber. Open end assembly; remove old lamp/seals (avoid touching new lamp glass). Inspect/clean the quartz sleeve; replace if cloudy, etched, or cracked. Lightly lube new O-rings with silicone-safe grease; seat squarely. Reassemble hand-tight, then snug—do not overtighten. Restore flow, power ON, verify strike, and check for leaks after first run.

Overview AquaEl Advanced Soil 3L - Plant is a premium, nutrient-rich substrate specially formulated to promote vigorous growth in planted aquariums. Designed to create an ideal environment for aquatic plants, this advanced soil provides essential nutrients and a stable base for root development, resulting in lush, vibrant aquatic landscapes. Key Features Nutrient-Rich Formula: Enriched with essential minerals and organic compounds to boost plant growth and health. Enhanced Root Development: Provides a stable substrate that encourages robust root systems, leading to stronger and more vibrant plants. Easy to Use: Designed for hassle-free application, making it an ideal choice for both beginners and experienced aquascapers. Optimized for Planted Aquariums: Creates an ideal foundation for aquatic plants in freshwater systems, supporting a balanced ecosystem. Long-Lasting Performance: Offers sustained nutrient release to support plant growth over time, reducing the need for frequent substrate replacement.

Overview AquaEl Advanced Soil 3L - Shrimp is a specially formulated, nutrient-rich substrate designed to create the perfect environment for freshwater shrimp. This advanced soil not only supports robust plant growth but also fosters a thriving micro-ecosystem that benefits shrimp by promoting beneficial biofilm development, which serves as a natural food source. Key Features Shrimp-Friendly Formula: Specifically formulated to support the health and breeding of freshwater shrimp while maintaining stable water parameters. Enhanced Biofilm Growth: Encourages the development of beneficial bacteria and micro-organisms, providing a natural food source that helps sustain shrimp populations. Nutrient-Rich Substrate: Enriched with essential minerals and organic compounds to support overall shrimp vitality and promote a balanced aquatic ecosystem. Easy Application: Designed for straightforward use in shrimp aquariums, ensuring a hassle-free setup that benefits both plants and invertebrates. Long-Lasting Performance: Provides a sustained release of nutrients to maintain a healthy substrate environment over time, reducing the need for frequent replacement.

Overview The AquaEl Fan Filter 1 is a compact internal filter designed to provide efficient water circulation and effective filtration for your aquarium. With a robust flow rate of 84 GPH, this fan-powered filter ensures consistent water movement, enhancing both mechanical and biological filtration to maintain a clean, healthy aquatic environment. Key Features Efficient Filtration: Delivers a steady 84 GPH water flow for reliable filtration. Internal Design: Compact and easy-to-install filter that fits discreetly inside your aquarium. Fan-Powered Operation: Utilizes a built-in fan to drive water circulation, improving oxygenation and overall water quality. User-Friendly: Simple setup and low-maintenance design ideal for both beginner and experienced aquarists. Quiet & Energy Efficient: Engineered for quiet operation and low energy consumption.